Viewing all customer Discussions for:

Door & Window

This piece is screwed into the window frame and holds in place the tension rod. The part has a H-719 injection molded into it.

One side of the part has 2410F inscribed on it. I need to order a set of these.

I have two problems with the channel balances on my Seal Craft windows. 1. Some of the balances do not stick with the window. They either stay in one place or move up and down the track some but not in sync with the window. Is there some way that they are supposed to click into the window it ... (cont.)

This part broke on the window itself. The channel balance appears to be in working order, but the part on the window broke, and so it doesn't "catch" the balance when the window is being lowered. I looked on your website, but I'm not sure what this part is called, or whether it can be replaced. ... (cont.)

Please see the attached pictures of the little plastic/teflon piece. At the top end, the piece has a hook and engages in the balance spring in the sash, and the lower end has a small hole/port where the spindle of the window is inserted to provide the balance for the raising/lowering of the window ... (cont.)

I have 5 windows with channel balances marked 28D. All of them spring up when the locks are unlatched. Would buying 29D balances solve this problem?

I think these were around the mid to late 60's hiLITE Convertible a product of ADOR/SECURITY U.S. PATENT No. 3,088,177 No. 0-198,383

Hi, I have 3 windows that need new channel balances. One window has balances stamped db102 2730, one window has balances stamped db102 2740 and the last window has balances stamped db102 2750. Can you help me order replacement parts please.

Hello, I am needing these small metal and plastic window pieces that travel across the edge of my window when you crank it out or back in. The picture shows a close up of it. Unfortunately I don't know the manufacture of my windows. There are not any markings.

I have some single hung aluminum windows made by a company called Alenco. They are about 18 years old and some of the balances appear to be failing. One, in particular, will not hold the window up. Others are very difficult to open. In addition, some of the pins that stick into the balances have ... (cont.)

what type do I need.

Im attaching 2 photos of the part I am trying to locate and order. one is the working slider and the other the broken. I am a homeowner in nj. this part is from a mirrored sliding closet door. Hope you can help me.

Hello, I had a cam that broke, and I ordered all the cams that your had, but they were all too big: (1) of 17-036 : LH Cam Pivot, 9/16" (1) of 17-038 : LH Cam Pivot, 3/8" (1) of 17-034 : LH Cam Pivot, 7/16" I have a picture in the photo album of the new cams alongside an old cam. The old cam ... (cont.)

Hello, My townhome was built in 1986. Windows are original. "Most" of my top sash guides are broken (or are about to break). My channel balance are all okay. Attached are pics of my chnnel balance in hopes that you could identify what top sash guide is needed to fix my windows. The numbe ... (cont.)

I can't find any name/number/marks on this assembly to identify it, I'm hoping you can help me replace this because the retainer threads have been stripped out. Measurements: 5-1/4" top to bottom (all measurements approx. hole center to hole center) 1-1/8" between the bottom two screw holes 2" ... (cont.)

My window balancers have the following code on it: k 23-1 Do you carry these? I need a pair I attached several photos of the two balancers that have a (k 23-1) stamped on each. The overall length of each balancer from tip to tip is 24 3/4"

I just want to make sure that I order the right part. My broken balance has the inscription D8 F0 28-1 in it. I measured it and it comes close, if not right on the 29" Series 385. Is this correct? How about the options? I'm not sure what the options are for and what I need to select as options. Than ... (cont.)

Trying to replace a broken latch, 82-107, purchased from Swisco. Trying to assemble on the door, but can't figure out where the wave washer and push nut end up (please see link below for a picture of the parts). I would appreciate step by step instruction with figures if possible, on how to assemble ... (cont.)

The latches in this picture use hold the window up, but now they don't hold and the window when you open it want to tilt inwards to you when you go to open it. Do have these parts and what all would I need? Thanks

Channel is 33" long. Has spring plus string and pulley system. Fits into a non tilt window. The words on the channel are as follows :32 5 HR CALDWELL. Width is 3/8"