Viewing all customer Discussions for:

Door & Window

Any one know where I can get this vinyl window trim? A bird smashed the glass in the fixed center glass of a bay window in a double wide mobile home. Vinyl window. to get the glass out ,these where wrecked, Trying to find some? It's the exterior that holds the glass in.

Hello, I'm looking for replacements for some old window operators. The first is an awning window with a 27" track. The glass size is 35-3/4" x 13-1/2". The arm is between 10-1/2" and 11" from the end to the elbow. Pictures 1-3. The second is a casement window with a 14-1/2" track. The glass si ... (cont.)

I have PGT single hung 50" wide lower sash metal window that needs springs replaced. I had these windows installed in 1995. The lower sash weighs about 24 pounds. The tension spring assembly without the white plastic ends is 30" long.The upper white clip on the end sicks out seven eights inches fro ... (cont.)

I have channel balances on 5 windows from the 1 mid 1980's that need replacing. There is a spring inside that is totally rusted. We think the number on the balances is 2810. Would appreciate help in finding replacements for them. Ray

I am looking for P.E Del Mar Roller, Part # 3522 Model SRO-89-HEX. Any chance you have it so that I can order a few?

I need a sash lock for a vinyl double hung low E Capitol window . Do you folks have any ? Thanks Tony

I'm working on a project which included re-screening 3 sliding patio doors. One of the doors(4'x8') fell apart as I took the screen off. I salvaged 2 pieces (pictured). I can't seem to find this exact size anywhere. I'm hoping you can help. Each leg of the corner is 3" long X 1" wide X 3/8" thick ... (cont.)

Can you help me with the above attachment. Thanks, Bill

I have some damaged pieces of plastic window glazing strips that I would like to replace. The windows are from 1993 or 1994. The only identifying label I was able to find has the following info: MFGR: MER-004-1 Series: 480 MST: 9-10x6-0 MVT: 47"x71" I ordered some from your company that loo ... (cont.)

Hello, I took out the broken part and it had these markings. Should I get the 4.5 lb S160? Thanks, Sean

Looking for white top sash guide for Milestone, single-hung series 2000 windows. Also, if you happen to know what balancer is needed for these windows (approx 32" w x 60" h), I'd appreciate it. Thank you.

It is about my storm door that is about 22 years old I have lost all the keys and need a new circle piece with new keys Who should I call? Where can I get this piece replaced ? Susan

I have a double hook lock mechanism where one hook broke. the side plate screws center to center are 11 inches. The plate from top to bottom is 11 3/4. The two middle screws are 3 inches apart from each other and a little bit under 4 inches from the screws that hold on the plate. The handle is9 ... (cont.)

I need to get a replacement balance. It is off a Keller window (see pictures). I think it might be a S377. I also need the plastic part that is screwed to the window which the top of the balance stops on.

My question is about the window top sash guide. Mine is length 1 3/4 , depth 9/16 , width 5/8. The nearest I can see on your site has a length of 2 3/16 , will this work for me or do you have one closer to my length?

Window locks ... hinges have serial number 4980947 on them. Not sure where to find replace mention locks

Would you have a matching handle for the outside? Just a blank plate. Thanks Bob

Original Part Numbers: 1) 1361486 L/1361483 HCR 2) 1361485 R/1361482 HCR (Picture Provided)

So the windows have a crank handle on the right side. This deteriated cover is on the left of the window looks like if it were to have a left crank. I need to replace on 7 windows.

I am looking to replace these two window channel guides, and the clips. The number should be visible in the phot, but to clarify it is 2920.