Viewing all customer Discussions for:

Door & Window

Looking for a crank for vent vue window. Putty in color ( stone?) Can I use the Anderson part? Will colors match? Thank you, Sheila

I am looking for the plastic insert in the window locking mechanism for 20 year old Craftline Windows. Do you have or know where to find the part and/or is the manufacturer still inbusiness and have replacment parts? thanks, Craig

please help identify and order the correct part for my window

Don't see any marking on the door or latch. Piece broken unlocks door from inside, missing in photo 1. Photo 2 is the part that the lever engages, looking at the door sideways. Photo 3 is the lock on the outdoor side of the door, opposite the part that's missing. Photo 4 is the part on the fram ... (cont.)

Hi the patio sliding door handle is broken. I saw a similar handle on your website: SLIDING DOOR HANDLE SET, 3-15/16" Product Code: 82-003 So attached pictures of what i need, can you please advise me if the handle I have chosen will match? If not please advise me what the best model for repla ... (cont.)

I need replacement latches and corners for a storm door window. Need all four corners two with a small pin at the top of the corner and one sliding latch. See photo that says seal.

Hello, From reading the other threads, my understanding is my PADO LATAO lock is discontinued and the 40-049 appears to be the best replacement. However, I'm unsure what measurements are the most important and whether you think I will need to drill holes or modify the 40-049 in any way. Attached ar ... (cont.)

I believe this is off of an Atrium window, the 150 series single hung. I need enough for two windows, about 24 feet.

See pictures attached and let me know if you have the replacement for this handle. It is an in swing door. I also need a closer for it Thank you in advance for your time and patience

Please let me know which of your balances I should select for the following window. Peachtree Window ALI-Class A G0492 Type AE Dimension

Hello, I believe what I have is a superior or a cetainteed window, there is a paper with plastic coating sticker on the inside of the vinyl frame on top worned out and I can not see any of the writing. The lower window is a tilt out from the top on the bottom window and it has 2 latches 1 on each si ... (cont.)

stamped BSL 2640. believe bottom is 15-002

Silver piece on bottom corner. Only says "Spect US" on bottom. I need one replacement. The one in the picture is in intact. The piece that needs to be replaced is broken.

I am searching for a pb mortise storm door lock, similar to the one you advertise (40-049). The lock handle is on the left side of the door. I think the item number is s843342 maybe. I need the complete mortise lockset brass (4o-183). The specifications are as listed on your advertisement. 8 1/8 " l ... (cont.)

I have several Tilt windows with Series 600 Spiral Balances That are 5/8" tubes 16" long and white tipped.Many of these are not working. I weighed the windows and they weigh about 12 1/2 lbs. Should I consider using the red tipped balances instead? Thank You Paul

My broken sash balance is 7#31. What would replacement be on your website?

Your product 55-184 did not have measurements. Please tell me what the inside of clip measures and the bottom width and depth is please. My clip looks just like the one you show. However my is 1-1/8" wide 1/2"tall and inside is 7/8". I need to replace several and want to make sure they will fit.I h ... (cont.)

I have a picture of the sticker from inside the window, but have a hard time to identify manufacturer. Plastic frame of the bottom sash felled apart and barely holding glass. Thank you for any suggestions.

Looking for the sash keeper in the picture. Screw holes at bottom are 1 inch apart. Height is 1 3/4 inches. Thanks

I ordered a steel keeper 89-021 and it the wrong part would you happen to have a steel keeper that i have attached in the picture?