Viewing all customer Discussions for:

Door & Window

I could not find any markings on this latch. However, I did use one of your single wheel that goes on the door bottom. If that helps. Also I believe this home with this slider came out of Canada.

Do you have latch handles for Pozzi casement windows? I've heard there are 2 generations of these handles and I'm not sure which ones I have but I think they are bronze finish. Thanks for your help.

The crank/handle is plastic through and through which is probably why it simply wore out. It is 3 1/4" long. The outside diameter is 14/32". The inside diameter is 10/32". KINRO is written on it. It belongs to a window in my shed.

Need a couple replacement arm operators. Only numbers I can find are 358-2. Thanks.

Hello, I am trying to find a replacement bottom door roller to a closet door I have. I do not know the part number and couldn't find any serial numbers on the broken piece. Please let me know if you guys are able to figure it out from the pictures and if you guys sell them as well. Thank you for you ... (cont.)

Hi, I'm looking for A set of rollers for my slider. I don't want to take the door apart before I have the replacement parts. Is there a way to tell which rollers I need from this sticker? Thank you, Julius

My Milgard windows balancer broken, its metal length is about 21 niches ( a little bit smaller than 21 inch. may 20.9iinches. My window is single hung, My question is this banker will fit my wondow.

I need the part number for this damaged balance. Your 33" series 385 option 3230 worked well for another window the last time I needed one. This current window is a smaller so I wanted to verify the correct part.

I need to replace part 81-018 I was inquiring to see if I can replace with part 81-149?

Hello I need to replace my Anderson sash balances. The stamping says 11600-17 and S4 10#31 8-8. I need to replace both right and left. Can you please recommend the appropriate replacement parts? Many thanks! Heather

Hi, I am looking for channel balances for 60-80+ years old aluminum windows in Philly. I just double-checked , house is built in 1974. These are duplex homes, outside is brick, all windows are original aluminum. This specific window has a sash of 22" x 24 1/8". Thinking of this product (and ... (cont.)

I am in need of a part for stanley/monarch bypass mirrored closet doors. I have attached the image of the part. It goes on the backside of the door and allows it to follow the top track.

Hello, I'm looking for replacement tilt corners for several storm windows. The existing nylon ones are stamped in and has guide. The closest match I see is the 95-015. However it doesn't have a guide, does this matter? I have not removed the bottom corners, which appear to be ok. Just in case ... (cont.)

Can you help? I have a couple of identical storm windows, each with different broken parts. I have attached two photos for reference. In one photo, I have overlaid the actual dimensions that I need for the top tilt parts. I do require a right hand tilt part and a left hand tilt part. In the second p ... (cont.)

I need a new handle....im assuming a an internal spring is shot. Handle just flops down.

This is left hand window crank. I need replacement for this window crank. I found item no 39-089 on your website. Let me know that 39-089 is the same item I am looking for or not? I also need for right hand crank. Thanks Bipin

Need help locating this locking mechanism for a pella screen door. Searching for 28090809117

Do you have Jalousie crank mechanisms and cranks? Looks like swisco.com is a source The 2

Cole Sewell St. Paul mm. Registration number is 100798960170073

I am looking for the Pella screen clips shown in the attached photos. They are similar to your 70-220 but not the same. Please advise if you have them or know where I could find. Thanks!