Viewing all customer Discussions for:

Door & Window

Need to replace fixed door clip with 80-051 replacement part that you suggest on your website. Will the screws line up the same as the older part. Also, what does the extension part on the left do (does it fold over) since the original part does not have this.

Please help me identify this part so I can order a replacement.

I would like to replace the attached tilt latch and I am unable to find a replacement.

Hi, I spoke to someone by phone this morning concerning replacement window spiral balances and pivotal shoes. I have attached some pictures of the replacement parts I am looking for and can be zoomed for better viewing: Image #FullSizeRender - is end on to show diameter Image # 0725 - is a brok ... (cont.)

Have found a part that does not work since the tooth did not extend out far enough. Need to have it extend at least 1/2 inch.

I need to replace channel balance for a sun air window brand the number stumped in the part is 2720 P the metal part is 28 inches long as well i need a window lock and 2 top casing. Can you help me please.

Please help me identify replacement parts -1/2" balance numbers are 2820 and 2730. I also need to identify top sash part.

Bottom vinyl sash tilt window does not stay open when lifted. It has dual hung 5/8" swirl balance tubes that resemble your series 600. Trying to find tilt balance shoe that has an upside down U shape pivot bar notch. Dimensions are roughly 1 1/4" x 1/2" x 2"

The counter balance has several numbers stamped on it; looking for the right one. 637 H16 9 98, measures 6 1/2 L X 2 7/8 W x 3/4 thick

I spoke to someone in your sales department earlier today about problems with the balances on a Kinco window and was instructed to send photos of the number stamped on the track and the top and bottom of each end. The photos are attached, although the number does not show up well. The number is 29 ... (cont.)

The pivot shoes are starting to wear out in our large (roughly 5'x4') windows. i am having a difficult time identifying which pivot shoes I need for the replacement. any tips on how to identify the proper parts would be appreciated.

Hi there, I've seen some great discussion on the board and hope someone could me out with some sliding door rollers. I have a contemporary house built in 1972 with Allen Stevens doors and windows, and the rollers on a 8 foot wide (4' doors) door failed many years ago. They are clearly marked with ... (cont.)

I am looking for a locking window latch for a vinyl clad crank out casement window Numbers on window are 566835-002 G53COFRR 092608-50A9 NFRC GLW-N-2 Right

Hi there, I'm looking for a non-tilt window channel replacement but uncertain which product would match the top and shoe of the one for my window (see attached pictures). The existing (broken) channel has the following markings "28 3 GX CMC 11" -- Measurements as follow: 1/2" Wide Channel Ba ... (cont.)

It says On the Bracket G*6050. Do you have a replacement for that Drawer Slider Bracket? Thanks

My Truth door rollers are 12+ years old, and barely roll. Can I replace them with your stainless steel 81-149 rollers? Will your rollers fit exactly? Once these are installed, it appears to be impossible to lubricate them, other than by taking down the (VERY HEAVY!) door. Any suggestions? S ... (cont.)

I don have the 19.25... stamp on my channel, the only numbers on mine are: 2448C on the end the rollers are located. The balances are 20 1/4" long and 1/2" wide. Can you Id what I need based on this info.

I need to replace both channel balances in my window. While I was taking them out the take out clips broke. I will also need that too. From a video I watched it looked like part # 16002 for the clips. The only number I found on the channel balance was 2730. The balance is 29 inches long and 1/2 ... (cont.)

Which balance do I need? The code stamped on the broken channel balance is "26 9 JV CMC 7." I measured the length and it's 27 inches for just the channel and 9/16" width. It seems like this is the correct one but I'm unsure of the weight.

Hi there, I have a bad spring balancer that is stamped with D26 8#31 4-81, any suggestions on which one of your units would be a good replacement? Thanks, Kevin