Viewing all customer Discussions for:

Door & Window

The part on the left is a Pivot shoe from a 1999 Alside Ultramax Double hung Measures are: 1/2" x 1 1/4" x 2 1/8" Night Latch part measures: 9/16" front to back, 3/8"w x 2" face, 1/4"wide core. I was not able to identify the Pivot Shoe in your online selections. Can you supply me with these parts ... (cont.)

link is 2 1/2 in. lower mounting holes are at 1 5/16 in. upper holes are at 7/16 in.

I need to replace sash balancer at Andersen window. The part number on the old balancer is: Part No:11600-17 and 11600-3 The dimensions are: 6 3/4 x 3 x 3/4. Could you let me know the replacement part number please?

HI, I just received my 6 lb series 152 coil balance and this fit perfectly. It has been 2 yrs since I have been looking to find a replacement... Thanks... Now I also received a Maxim Multi-point lock Slider (handle) (also from you) , but I don't know how to open the window. It snap during the co ... (cont.)

I need two coil housing pivot s I think your 15-087 matches mine and two coils S180-7 going to try to send pict

I believe u no longer make this handle. If so I need help with a replacement model. I have included a bunch of pictures.New handle or new model number that will work with my existing holes

33x1/2. Can you help -

I need to replace existing ill-fitting and ugly handles with ones that look like this one. I saw more than one that might be the replacement and want to be sure so I get it right. Thanks for your help.

i have a plastic sleeve that covers the spiral spring unlike your 600 series balancer. The length of the plastic sleeve per your measuring instruction is 22" but the blue plastic bushing is recessed about 1/2" inboard. The overall length from one end to the other is 23" with the rod completely pus ... (cont.)

Hello, I have very similar pull latch on my balcony sliding screen door. Looks almost like your latch & pull 84-227 and very similar to your latch & pull 83-116. I am missing a part that keeps the door locked. All I have is just the holes for screws. Could you please look at my photos and let me kno ... (cont.)

This pivot bar is from the lower sash window. I could not find any numbers or names for the window manufacturer or the pivot bar itself. I have 14 windows with 2 pivot bars per window. Most are rusted due to our Florida salt air and need to be replaced. Thanks for your help. Susan Shirley ... (cont.)

Hi Guys, I've got an old sliding patio screen door that needs the screen replaced. The spine in the door now is not the original, and is too small to properly hold the old screen. I replaced the screen and spline years ago and matched up the original spline to what was at the hardware store. ... (cont.)

Hi, I have a couple of different Andersen Windows that need new balances. I prefer not to take them apart until I have the new balances, but I need to figure out which ones to order from you. I am hoping the dates and other data on the windows will tell you which ones. These windows are circa 1980 I ... (cont.)

Hi, I need to buy replacement balances for a tilt window. The length of the balances are approximately 34 and 3/4" (not quite 35"). Should I buy the 34" or the 35" balances? Also, the balances from one window are attached to the balances of the adjacent windows. Since I have to detension the adj ... (cont.)

Hello, I'm looking to replace my Truth 45251 widow crank to a folding-style crank, and am looking for advice. I've attached pictures. Any help would be greatly appreciated. ~Andy 40050

I have certainteed windows purchased in 1995. I have been told today by certainteed the part numbers are 86121,86131 and 86141. I have 16 double hung windows I would like to replace all the tilt latch assemblies. the windows are white. Can you please verify the parts I need and advise price and ... (cont.)

I'm selling my house and need new coils. Or at least, the support works around the coils. What do you recommend?

I have a older sliding glass door unit that know one seems to know who makes these parts or the glass doors. They have no markings on them and seem to be 30 plus years old. thank you, Brian

Are you able to id

Dimensions starting from too where my finger is. 7/16 across, 9/16 down, 1/8 across and 1/4 back up. Your assistance is much appreciated