Viewing all customer Discussions for:

Door & Window

I need some replacement hinges for a Guardian storm door. There's something similar on your website, but I'm not sure the pins are the same size. It says it's for a Larson storm door. The product code is 40-153. Is it interchangeable with a Guardian storm? And will I have any trouble returning ... (cont.)

I'm not sure which balance I need for a Caldwell 28 4 CO. I think it would be 19-005 top, but not sure on the shoe. Maybe 15-005? so Series 380? Please see included photos. It is for 29" length and 1/2" width.

Have two wooden sash windows with broken old spiral balances. Would like to replace. Windows have a routed channel 5/8" on both sides. Windows are 24" high approx. 8 lbs ea.

I have Ware windows on a mid 1960s home that I just purchased. I have included a picture and hoping you can help identify the part required to replace. Image A shows a crank in a window that is complete. Image B shows the only window marking that I can find showing it is a Ware window. Image D s ... (cont.)

I purchased pivot lock shoe 15-134 and pivot bar 26-040. When I tried to place the pivot bar into the lock shoe it did not fit. Could you recommend a lock shoe of similar dimensions that will accept the channel width of the 26-040 pivot bar. Thank you

Dear Sir / Madam. I am looking for replacement window sash pulls for sliding windows. The existing pulls are white plastic, 3 7/16" long with 3" centre screw holes. They look identical to your Window Sash Lift Handle Product Code: 26-116 with different measurements. Do you have such a sa ... (cont.)

I'm looking for a replacement lock for my window built in 1990. Mounting hole measures 2 and 1/4". The hardware width is 1 inch. Attached are front and back photos. Please help me find a replacement. Thank you very much. Sincerely yours, Carol

Please let us know if we can get this right away. Thanks!

Please help me choose correct screen pin replacement. Photo is of exsisting pin. It is spring loaded, 1.5 inches long. I do not know how to measure the diameter. Thank you.

Total pin length 1 3/4 inches, Head to end of first shaft length 1/2 inch, remaining shaft length 3/4 inches. Head width 5/16 inch, bottom shaft dia. 1/8 inch, shaft diameter right below head 5/16th inch, I am missing a spring that should be on it. My screen storm trim is 3/4 inch by 5/16 inch. ... (cont.)

. We need left and right window screen clips for windows purchased about 22 years ago. Probably 5 of each. Window cleaners are careless!

Good Morning, I need to replace the tilt latch on my window. I have already removed the broken one and can not find any manufacturers name or markings on the window or the latch. The only Mark on the latch is an R (for Right I'd assume) and the number 98. Please see attached pictures for measu ... (cont.)

Attn: Customer Service Can you supply me with these Pella screen door glides or tell me where to get them? My screen door is probably about 15 years old but the glides break. Let me know what you recommend. Would appreciate any help you can give me. Thank you.

We need two BSI 3600 LB balance replacements and one BSI 3000 FL balance replacement for our white vinyl tilt windows approx. 15 years old. They look almost exactly like the ones in your "how to replace" video. Can you help? We can email pictures if you need them.

I have come across a screen door that is missing (top I think) rollers and I am not sure what rollers may work. I carry several types of rollers but none of them seem right. It has 2 non adjustable rollers on what I believe is the bottom that are fine and there is a large gap from the door top to th ... (cont.)

I have a crank casement window in the ceiling of my bathroom. Our house is over 30 years old. The base of the mechanism has a metal plate marked PAECO with the serial number 102041. Any possibility of replacing the chain mechanism?

I am in need of a replacement part for my Rusco Window. The piece that broke is the latch that releases the bottom window to fold in. Please see attached photos.

window part needed

We have 2 windows that are hinged on the left in which the crank is stripped. I believe the arm is 13 inches. We're also looking for a price on weatherstripping. The picture above is a little large, but we made it work. Also, we need a new lock mechanism for the same windows. Thank you! ... (cont.)

This is a peachtree door roller purchased around 1973 with a 1 1/4" roller. Please contact me ASAP, thanks, Josh