Viewing all customer Discussions for:

Door & Window

Found S380 28" that looks like what I need. Not sure of the "strength" rating. My old one is stamped 2730G. Your choices are in the 26xx range of numbers. Mine is nominally a 3ft by 3ft single hung sash, vinyl, originally made by NW Aluminum in Washington state. I also need to top stop that secur ... (cont.)

Hi, Do you have this window roller and carriage, that closely resembles the attached roller? ts for old aluminium Stegbar sliding windows. I need 10pc. Thanks

2 off patio door rollers part no.truth 31761

This patio door handle is from around 1976-81. I have tried to show all markings. The outside handle has the name DOrWALL on it. The inside has the number 120 imprinted on it. The outside handle is 6 1/4" long.The inside handle is broken off at the top but is about 5 1/2" long. The inside handle ... (cont.)

This grip has come from an Anderson gliding door. The center to center for the mounting screws is 5". Can you help? Thanks! Andrew

is 30-028 avail in lefts and rights ?

I need to replace screen clips on my screens because the broke off due to age. I noticed a piece of the clip is still between the frame. It is the end piece of the smaller part of the clip; the piece that would align to the hold to attach the two pieces. Would I need a tool to remove this piece? ... (cont.)

Need replacmenet sahs balance. Cahnnel lenght is 19 7/8 Please let me know which one I should order

I am looking for these parts, please let me know if you can help. Thank you.

The attached photo is of a Jeld-Wen casement window operator that has stripped teeth. The date of manufacture from the date on the window is 01-05 and the "model" on the operator is "Entry-Gard"

I need to replace a window crank on my mother's window. Inside the house, it would be the right window as you face the set of 3 windows side-by side. The crank on the left window has R30842 imprinted on it, but I need the opposite one for the other window. Someone did replace it for her a few ... (cont.)

replace part

Hi, I have attached a picture of the sweeper and keeper for the window locks. I have several that have broken and need replacement. Since the original windows are from Philips that went out of business. Philips was purchased by Kinro but the window locks and keepers from Kinro do not fit the Philip ... (cont.)

I have an Andersen window and the sash balance needs to be replaced. I need to identify the parts I need. The marking on the window and the size is as shown below Can one tell the part needed from below or do I need to remove the existing balances as shown in the video. ANDERSEN Windows A/W ... (cont.)

I am looking to replace a broken tilt window latch. I have attached photos of the removed broken latch as well as its still-installed partner. The latch slides on to the edge of the window and is held in place by a screw. The latch is approximately 2.5 inches long and 1 inch wide. There are no m ... (cont.)

The sash lock / latch on our casement window (opens out and locks on right side) broke and I need to replace both parts of the locking mechanism; the part on the frame directly on the window as well as the part on the frame around the window. Is it part 38-205? I am sorry no markings were found on ... (cont.)

MY WINDOS ARE ALUMINUM SO WILL THE 15-070 WORK IF I CUT A SECTION TO POP IN THE NEW SHOE THE DIMENSION ARE THE SAME 1 1/4 5/8 2"

Two different size windows that are from the same mfg. company in the same home need channel balances replace that are broken

Can I just buy the plastic shoe for the part below? Is it handed L.R?

I need this window part for anderson casement in white # 7191-32 L bought from swisco 136116 R and its wrong i'd like to return and get the one below thanks