Viewing all customer Discussions for:

Door & Window

We are trying to locate this part for a customer. Please let me know if you can help! Thanks!

This is a 45 year old patio door that I would like to convert to be a key locking unit from the exterior. The only marking I can find on the door is "Hilite Convertable". It has a 4" spread for the screws and the door is 1" wide. Can you suggest any new lock set unit I can purchase from you? ... (cont.)

Hello there, I live in a 20 year old house which we are currently selling with the original windows and need to replace a piece of trim that fits behind the latches and under the glass on the top pane. I would be eternally grateful if you could help me find this part!I am in a bit of a crunch to rep ... (cont.)

Our sliding patio doors were installed by Alcoa. The pull and latch for the screen door needs replacing. I have been unable to locate a similar pull. There are no markings on the pull. The problem has been matching the distance between the screw holes on the back of the pull and its edge. ... (cont.)

Hello, Can you replace these?

I'm looking for replacement balances for Anderson window. The numbers stamped on the existing balances are J48 519 10-88 as well as 11600-17. I can't find the numbers on your site that would match, so I'm looking for a suitable replacement.

Here goes. I have a heavy storm door that hangs from hinges that are all one track with openings for the three hinge pins. Whee the door bless open in a wind storm, all the hinges were bent and pulled free from the track. They are made of metal. So my question: would the nylon universal pin replacem ... (cont.)

We have 5 windows with this type of crank out window in the home we just purchased. We haven't had any luck finding replacement handles. Any help you can provide is appreciated.

I need to replace this mortise lock. Can you help? Please note: I used the diagram for the measurements only. When the latch is in the UP (locked) position the keyway is at a 45 degree angle. I think the lock I need is 82-218. Can you confirm that? Thanks!!! --Danny

The latch broke off a few years ago and am now ready to replace it. I want to make sure I order the correct part (83-115?). I've enclosed two photos. Please let me know and I will then order the part from you. Thanks for your help.

What are the best techniques for removing knife latches from a window frame so they can be replaced. It is difficult to release the tiny stop. Thanks

Hole is 1 1/4. Door is old storm door. Will this latch work? Door is only 3/4 inch thick.

INSTALLED NEW ROLLERS ON SCREEN, BUT CAN SEE LIGHT THROUGH BOTTOM OF DOOR. IS THERE SOME KIND OF ADJUSTMENT TO SET DOOR? #1997063 ROLLERS

The old storm door has holes that are 1 1/2 inches from top hole to bottom hole on center. The Center hole is 3/4 inches from each hole. The door's edge is about 7/8 inches to center of center hole.

I'm looking for a replacement handle for our sliding glass door and the screws to attach to the existing holes is a 6 1/2" center to center. Any chance you have something that would work for that? I don't need the part that locks or that is in the door itself. Mine is black metal with a med colo ... (cont.)

I wish to replace the sliding door lock shown in the pictures above with one with a key on it. Can you tell me which lock i need to buy please?

I am trying to see if these clips look familiar. I need about 20 balances. The number on the balance is 1910. Do you have something that would work?

I have an out swing exterior metal door. I would like to enjoy a screen for air and light, and glass storm for light, requiring the main door to be in the open position . Is this possible?

I need 34 rollers to complete a job I am working on here in Florida. Siminton sent me to you guys for the part. They said it was from the old Lighthouse Products line. Kenny Door And Glass Company

Hello Experts! I am sending you a picture of left hand side lock and handle (which is all right) , but the right -hand side lock is broken and the handle is missing. ( color -white) Could you give the parts number to order? Thank you all the time.