Viewing all customer Discussions for:

Door & Window

Hello, Attached is a front and back photo of the window coils that I need. I am in need of 16 of them (for 8 windows). They are all the same size and type of windows. Please let me know what I need so that I can order them asap. Thank you Rikki

Do you have any with a 7/16 spline

Replace rollers Lincoln 6' sliders 1986 which one?

I had 22 Certainteed vinyl relamcent windows installed in my home about 15 years ago. About 6 months ago one window would not open unless we applied a great deal of force. A contractor who was working on another project showed me the problem was a bent tilt window latch. Its an angle iron with ... (cont.)

I have a Norco casement window with a broken Truth operator. I identified the operator as a right hand 15.08 - with a 9 1/2" offset arm. I work in the industry so I am familiar with the hardware. I did not see it on the current Truth web site, so it may have been discontinued or replaced with a diff ... (cont.)

I'm having trouble determining which replacement balancer to order. I have several non-tilt single hung windows in my home that are stamped simply 26 4 (BSJ sideways is also stamped) PA. Do I need to weigh the sash to determine the strength of the balancers/ Thanks, Jim

stamp on back of old channel balance is 284D0 do I order 2840?

I have a bath room window that needs new springs to hold it up---it weighs 10lb--it is the 190 series 1/2 in width spring-------I think it would be the 540---it has 17in of window travel-----wish you had the specs for each spring on the web page..

I need replacement part. 9/16 thick. 1 1/4 wide. Series 500a dh. 7 pound. I need 4 parts

Our circa 1977 home with the original aluminum frame windows (maker unknown) are starting to breakdown. I need to identify the correct channel balance (I hope I am using the proper term). Will you please help me identify this part and possible where I can order them? The enire piece (pictured) i ... (cont.)

Looking for some help in replacing a window lock for sliding windows. The windows are a no name brand installed by the builder when the house was built in 1999. I have included some pictures. Any help would be greatly appreciated. Thanks, Mike. FYI-in the second photo the item in the photo has on ... (cont.)

could someone help me identify this part for replacement? they measure 15/16 wide, 1 15/16 tall, 3/8" thick and the hole where the window sash connects to it is 3/8 wide and just under 1/4" tall. also my spiral window balances are 3/8" diameter and are all white )not bare metal is there a replacemen ... (cont.)

I'm hoping you can help me, we are looking to replace one of the window operators for our casement window. Attached are several photos with measurements. We have tried standard replacement operators from the hardware store, but have not had any luck. The depth of the crank is too shallow on most and ... (cont.)

Hello I have Lindford windows (they are no longer in business) and I need to replace my window balances as they have broke. Looking at your website I believe I need the S380-27 with 19-005 and 15-005. Now for the option is where I'm not entirely sure. my window weighs 50 lbs (3 pane glass) I ... (cont.)

1.This simple rubber strip runs the outside of the window that doesn't open. I'm looking to replace a 70" section. The windows are Atrium brand but I couldn't find a make and model 2.There are 2 delicate plastic clips at the bottom I need to replace. (Picture #3)

Need two left handed full replacement units. The part numbers on the back are 0P05-7554-03 Date of 05-011-05 Another number is 65276.

Need one part per picture attached. Square receptacle is 2 1/2" X 1 5/8" locking shaft length 4"

Does your replacement roller that fits the sliding Anderson screen come with the screws?

I am looking for a smaller roller that is 1 in and 3/4 height, 1 3/4 depth and 3/8 wide. the wheel is 1 1/4. do you have any in stock that i could order?

I am looking for part #Wi1652 which I believe measurements are 2-5/16 between Holes, 2-3/4 x 2-3/16 x 1. Do you have this size? thanks Robert