Viewing all customer Discussions for:

Closet

The house is 47 years old. the closet doors are original the ridge that the door rollers slide on is worn I need a new base 59 inches long, 3 1/8 inches wide, with 1 1/2 inches between ridges (measured from inside rail to inside). The doors with frame are 1 inch wide.

I've scoured the internet trying to figure out the design of this top guide. The bifold doors will not stay in the guide rail no matter the adjustment at the bottom and I am now wondering if I'm missing a set of guide wheels and/or springs. The house was built in the early 1980s and there are no mar ... (cont.)

I have been looking for this white plastic piece for a sliding door for two weeks, checking every hardware store in the city. Its for a folding closet door. Thanks Garret

I received bottom track for my metal bifold door, 21-401. Note 2 photos. I think you refer to the pieces as floater and pivot ? Your track is less wide as my old one. My floater piece (under the spring) is wider than the opening on the track and does not go in.I want to order the 2 parts (floate ... (cont.)

Hello I am trying to use older metal bifold door pivot pins with an adjustable bottom bracket (photo attached). The issue is the plastic bushing does not work in the adjustable bottom bracket. I am using this setup on a laminate floor. Do you have a bottom bracket setup that can accept the pin o ... (cont.)

Hi, Just moved into this house and the exterior wall has hinged panels that open up to a vent to allow air into the house. The handles are pretty old and beat up so I'd like to replace them. Don't see any manufacturer's markings. Thanks for you help. Todd

Hi I am looking for a replacement roller for a mirrored closet door roller is approx. 1 1/4 in wide and the roller assembly is approx. 3/4 in wide by 2 1/4 long the assembly is flared on top to slide into a track on the mirror frame and there is a slot for a screw at the opposite end to the roller f ... (cont.)

Which replacement track do I need? I have Stanley Works mirrored closet doors. The bottom rollers appear to be identical to your 23-041. The original track is 3 7/8" wide and the two individual door tracks are 1 5/8" center to center

I have four of these wheeled glides on two sliding mirrored closet doors that need replacing in a house we just bought. I suspect we need hardware for the tops of the doors as well but the parts are missing. Do you have these glides available? Would you know what the top hardware would be? I appreci ... (cont.)

I have been looking for this part everywhere ... but can't find it

need one of these in the picture. It says Acme on itThanks for your help in this matter.Terry S.

This is affixed to the top of the closet opening and the channel slides into it. I do not know the manufacturer of the sliding door.

Door track

My sliding mirror door roller was not working. I went to our local hardware store but they don't have this kind of roller. The top of the roller was marked as U.S. PAT 5,673,516. I need two of this roller please. Thank you!

Good Morning, I am looking for some steel bifold door hardware as in this picture. I am located in Canada and am wondering if there is somewhere in Canada I can order from. I work in an apartment building where these doors are probably 40 years old and some of the hardware is starting to fail. I ha ... (cont.)

I receive the cap, but it will not fit. I thought I had right size. Please let me know if I can return this and get correct one. Please see attached pic and let me know what I need. I also order your 21-111 and that was just bit small and it would not fit. I have return both back. Lets try 3rd time ... (cont.)

The plastic piece slides along metal track under the sliding doors. I need 12 of them.

Hi, I'm looking for a replacement part for mirror folding closet door. Specifically, I'm looking for a replacement bottom pivot pin. It appears that the closet door hardware parts, and perhaps the closet doors, are made by COX USA. From my Google searches, I think I need COX USA 26-055. Do you offer ... (cont.)

My three-year-old son pulled very hard on a bifold closet door and bent this screw. This inserts into another piece of hardware that runs along a track. Any chance you know a replacement part?

Top of second bifold door to slide in channel