Viewing all customer Discussions for:

Closet

The posted photo from a 1970's house. All double doors. Offset looks like 3/8", length 2-1/2", roller dia 3/4". Marked "Kennatrack" and has a capital "B" with a circle around it. Can you help with a replacement part? I guess the alternative is to get a new track and roller set.

I have Full Vu folding doors Leigh with a stamp on the inside that says Leigh Prod 5702-2. I think they are bottom pivot. Looking at your catalog it looks like I need six of the 21-054 and two of the 21-048 or two of 21-051. What do you think?

trying to locate a pocket door guide like this. Please help. Thank you.

I am interested in using your one-piece closet door guides. The doors are 1 3/8" thick and are in carpeted rooms. I think I need item #23-209B. Do I need to use a carpet riser with the guide? If so, which is the best one to use with this guide? Do the holes in the carpet riser match the holes in the ... (cont.)

I've been everywhere looking for this part and I cannot identify it.

Hello, I am looking for a floor track to install on regular sliding closet doors. The door thickness is 1 1/4,the lenth is 48 inches. Do you have any floor tracks instock to do this?

Can you recommend a replacement for the rollers shown in the pictures attached. The rollers hold up doors which are heavy. I think the offset is 1/4 inch.

I found the pin cap (21-100) but, I can not find pivot pin bushing.

Monarch mirror bi pass doors Wheel diameter 1.5" Bracket 1.75" wide x .5" thick Overall length top of bracket to bottom of wheel 3" If not the bracket with wheel maybe just the nylon wheel with metal ball bearing hub. These doors are 30 x 78 and weighs 52lbs. There are 4 door with 2 wheels on ... (cont.)

Are These guides as strong as the original ones? I had gotten some from an old established glass store in Lancaster, pa But they broke into pieces when installing them. As if they were old an brittle

Good Morning, I have old Strato-Fold metal bi-fold doors that I need replacement hardware for (Serial #26629). I would like to speak to someone asap, to make sure I'm ordering the correct part numbers. I need; Caps (21-105)?, Cone Springs (21-256), and some Pins (complete w/caps & cone springs). ... (cont.)

Hello, what is the differance between the 23-199 and the 23-225? Thank you Freddie

I'm looking for track that goes with part number 23-041.

Hi, I have a set of doors on track in my bedroom that was built in the 70's. The nearby door shop told me that this track hasn't been made for 20 years. I am looking for a similar replacement track, if it exists, and its matching wheel set for my slide doors that are still in good condition. Plea ... (cont.)

I have the 6' (3'+3', 2 doors) mirrored glass doors in my bedroom. I need a resource to find the bottom railing (approx 3" wide w/ 2 tracks, brass look). Mine has tarnished and needs replaced. Where can I find one ??? Thanks- T

I am in need of several bifold door pins/pivots. These look very similar to the pictures from "Rochester". Do you know if that fellow's issues were taken care of by the pins you suggested? Thanks, Mike

I have broken both rollers on the bottom of one Stanley sliding wardrobe door. They appear to match your product code 23-041. First question: how do I remove the old assembly from the door? Second question: how hard is it to install new ones?

I am trying to find a replace roller for bypass closet doors. The photo shows a view of this part from the front of the door. The roller diameter is 7/8". The offset is 3/8" (I believe either a 3/8 or 1/4 offset will work. Unlike most hardware the roller is grooved. I would be interested in eith ... (cont.)

Is there any other pin I can use other than the 21-108 PIN CAP. So that I don't have to remove the track where the pin slides back and forth on. Thank You. Dennis.......