Discussions for Closet : SWISCO.com

Strato-Fold bifold door parts 26629

Good Morning, I have old Strato-Fold metal bi-fold doors that I need replacement hardware for (Serial #26629). I would like to speak to someone asap, to make sure I'm ordering the correct part numbers. I need; Caps (21-105)?, Cone Springs (21-256), and some Pins (complete w/caps & cone springs). ... (cont.)

How do you adjust the 23-028 Mirror Door Roller?

I just purchased 4 Mirror Door Rollers from Swisco...the onesthat are currently on the doors do not "adjust" up or down when I turn the adjustment bolt. I believe that the center hole where the bolt screws into the top of the "wheel housing" is supposed to be threaded...all four of mine are stripped ... (cont.)

23-199 vs 23-225

Hello, what is the differance between the 23-199 and the 23-225? Thank you Freddie

Do you carry replacement track that works with the 23-041?

I'm looking for track that goes with part number 23-041.

mirrored closet door track

Hi, I have a set of doors on track in my bedroom that was built in the 70's. The nearby door shop told me that this track hasn't been made for 20 years. I am looking for a similar replacement track, if it exists, and its matching wheel set for my slide doors that are still in good condition. Plea ... (cont.)

Replacement mirrored glass door railing

I have the 6' (3'+3', 2 doors) mirrored glass doors in my bedroom. I need a resource to find the bottom railing (approx 3" wide w/ 2 tracks, brass look). Mine has tarnished and needs replaced. Where can I find one ??? Thanks- T

bifold door pivot pins

I am in need of several bifold door pins/pivots. These look very similar to the pictures from "Rochester". Do you know if that fellow's issues were taken care of by the pins you suggested? Thanks, Mike

Replacing mirror roller assemblies

I have broken both rollers on the bottom of one Stanley sliding wardrobe door. They appear to match your product code 23-041. First question: how do I remove the old assembly from the door? Second question: how hard is it to install new ones?

Bypass door roller 1/4" offset

I am trying to find a replace roller for bypass closet doors. The photo shows a view of this part from the front of the door. The roller diameter is 7/8". The offset is 3/8" (I believe either a 3/8 or 1/4 offset will work. Unlike most hardware the roller is grooved. I would be interested in eith ... (cont.)

LEIGH DOOR MIRROR BI-FOLD DOOR..

Is there any other pin I can use other than the 21-108 PIN CAP. So that I don't have to remove the track where the pin slides back and forth on. Thank You. Dennis.......

Replacement Part for Sliding Closet Mirror

I'm needing a replacement roller part for a sliding closet mirror door. Thank you, Brent

Width of flare for the 23-043?

Hi, can you tell me what the width of the flare portion of this part is? Thanks.

Floor Guide Product code 23-209

I assume this floor guide is adjustable. My doors are 15/8 thick

bifold door parts

Need pins to hold door on track

Replacing the wheel of 23-043 with 81-228

The wheel looks identical to the one used by the 23-043 assembly. I'm fairly confident I can drill out or grind of the rivet holding the existing damaged wheel. Do you sell a male/female shoulder bolt or a replacement rivet for the 81-228 wheel? Thanks, Don

23-176S as a replacement

Can I replace my tricycle closet door roller with the 23-176S. The last set of rollers lasted only 3 1/2 years.

23-501 Track Installation

The width of my closet opening is exactly 60" or five feet. It appears from your by-pass track kits that I would use the 5ft track #Product code 23-501 that the track is only 59" vs the 60" opening that I need. How does this work? Do I center the track on the header and leave a gap of 1/2" on eac ... (cont.)

Mirror Sliding Closet Door Top Roller

Hi, Do you have something like this? I need one for the left top side (facing door from front). Thank you

How to fill a gap between floor and closet door

I replased the carpet for wood floors and now there is a gap between the floor and closet door how can i fix that gap to make the door to work again

roller with 1/8" offset for custom pocket door

Several years ago i made my own pocket door and used what i believe is a 1/8" offset with a 3/4" wheel. Its not rolling well due to wear. Do you carry a 1/4" offset with a 3/4" wheel? Do you carry a 1/8" offset with a 3/4" wheel?

Viewing all customer Discussions for: Closet

Viewing all customer Discussions for:
Closet