Viewing all customer Discussions for:

Drawer & Cabinet

I need replacements for some broken drawer glides on an Ashley furniture dresser. The measurement of the glide is 1/2"L x 5/8"W x 1/16"D. I have attached photos. Thanks

Looking for a replacement for the attached door handle from a Yound Hinkle cabinet. Numbers on the back say KBC N8129 or N8139. The one number is hard to distinquish. Will need all hardware parts for this handle/closer. it's about 5 1/2" long and 2 1/2" wide. Thanks so much.

Please advise if you have sockets that can be used to replace attached sketches.

I need to replace 6 hinges. I need these identified so I can order correct hinges. Thank you, Richard

As you can see both my brackets for my drawer have broken. they brackets on the left illustrates how the bracket is broken. and the one on the right shows how it must look when in original condition. But both of the brackets are broken for the under drawer mount. please contact me to resolve this pr ... (cont.)

I need 8 pair of these drawer sockets. Dimensions are as follows: Mounting plate 2"H x 1 5/16"W, socket depth is 3"D. Glide socket I.M. is 7/8"H x 7/16"W. It comes from a cabinet by Sears and is about 10 to 12 years old. A number stamped on the back (102). I'll send photos. Thanks, Mike ... (cont.)

Hello, The house we bought has center-mount drawer slides with a central metal channel attached to the cabinet, rollers on both sides of the cabinet opening that the drawer sides roll on, and a white plastic glide screwed to the back of the drawer. Most of them work just fine, but a few of the pla ... (cont.)

Hi! I'm looking to replace drawer sockets that have broken. They are similar in design to your mode 32-014, except instead of 7/8" slide opening, mine are 1 3/4" to hold heavy duty slides. Do you have anything like this or know where I can find them? Thanks!

I have a customer with bedroom sets manufactured by Henry Link and Young-Hinkle. The furniture is approximately 30 years old. The wood center rail that the drawer is guided by has deteriorated on three drawers. The wood appears to be poplar. I measured a sample and it is 16" long, 1-1/16" wide, ... (cont.)

I would like to find a source for replacement Drawer Track Back Plates for my cabinets. I've attached a photo of the Original Equipment back plate. The OA length is 1-1/2" and there are two fastening plugs that extend out the back of the plate. The inside of the plate is 3/8" x 1" to accept the dr ... (cont.)

I need to find a set of replacement drawer sockets for a kitchen drawer, to replace the socket shown in the picture. I see no brand name on the sockets or cabinets, but the brand "Liberty" appears on the hinges for the kitchen cabinets. The sockets needed are a left and a right side. Each is 3 3/ ... (cont.)

I'm looking for a replacement part for a Simmons Double Dresser I bought in 1995. The bottom drawer has come off its track/glide. The dresser model # is 6303. The metal part is roughly 5 3/4 inches and has ball bearings.

how does the ball stay in? is there a spring inside?

I purchased replacement Kenlin case runners today and am also looking for the corner slides for the same dresser. Hopefully you can tell what I need from the picture. Thank you!

Attached are pictures and drawing for a SWISCO drawer guide. Looks like 32-031 but it isn't. As you'll note the guide support "tongue" is in the middle to ride the rail. Pls identify so I can place an order for four.

A rear drawer stay seeking at least 2 ea. Yopur help is most appreciated !!! Thank you Robin

Attached is a picture of a rear drawer bracket. We have 2 so far that have failed, age I assume. I haven't been able to find these locally. Would part 32-018 work as a substitute? The bracket is 3 15/16" long, the back "rectangle" is 1 1/4" x 2" and the "inside" where the current drawer hardware wo ... (cont.)

I am looking for what is commonly referred to as china hutch glazing. Where can I purchase this?

My corner glides on the dresser are broken do you sell them? Or where can you get them??

Hi, I am looking for a rear slide bracket for my kitchen drawers... it's a Unigrass 6600 system... can you help me finding a replacement part? tks Norbert.