Viewing all customer Discussions for:

Other

Needs new channel balances 24TG on three windows. It seems to be the inside balances that the feet are broken. The old blue ones with metal. Windows are around 32 pounds.

I have a General Aluminum window with (we think) a 29" spiral balance casing that has missing clip/cover on both sides so the window will not stay in place when opened. I've attached a photo of the part from a working window that isn't on the broken window, stamped with a #63. Can you advise what th ... (cont.)

Hi! Can you help me too find out channel balancer 24HDT.Thanks

I have a broken keeper and I can't find a replacement anywhere. This is from 1550 sliding screen door installed 10yrs. ago.

We have PGT sliding glass doors that we'd like to be able to lock with a key on both the inside and outside. These doors are never used and don't want to take any chances with our little one getting outside where there is a pool. We have a normal swing door right next to the sliders, so no worries ... (cont.)

Coiled tubular balance spring. Plastic tube. 3/8" Diameter. Tilt Window.34 3/4 tube length.

I need to replace this pin and have absolutely no idea what to order. Thank you. Regards, Denise

Looking to replace broken dresser handle (see photo). Company has apparently closed. I have the following information available: Model # - G5122-05 Chest-of-Drawers Manufactured - 10/2007 It does also have a UPC code if needed.

Good Morning, would you please help me identify this part so I can order? It is for the left side ( looking at the window from the outside.) The handle and cover are ok, but the window will not "roll out" any more. Thank you

Hi Swisco, Could you help me find a suitable replacement for the horizontal sliding window pull latch pictured in the attached photos? It is 3" long; not sure what window manufacturer made it. Thanks!

Hi, I'm confused whether I need to buy Series 380 or 385 Channel Balances. Top looks quite obvious, but not sure about shoes (should I include the wing to the length?) FYI, It was 0.5 inch wide and 21 inch long. Also I can see "20 4 KP CALDWELL" Thanks, Junho

hello, I'm refurbishing all the 20+ vinyl windows in my house, cleaning them, making a list of broken or missing parts, saggy springs etc. All the windows are single hung, vinyl. I have lots of questions , such as 1.) Can you please advise how to interpret the codes on the springs? For example, on ... (cont.)

Referencing my recent order for an EntryGuard Dual Arm Operator (#39-032) and other parts, when installing the Operator, the lower left side (looking out) sliding hinge failed (see attached photo). Please advise what part number I need to order to replace the subject hinge.Thank you,Barry ... (cont.)

casement window hardware. Crank in middle of mechanism. 2 equal-sized gears left of crank

Hello Can you please help me to identify the model numbers for these parts so that i can place order. Currently the closet doors move out of the rail when sliding, i am thinking to replace the upper guide , lower guide all with wheels along with railthank sPaul

This is what I'm looking for

While I was cleaning outside I found a piece from my window that I identified as a glazing bead. I searched all of my local hardware stores, but none of them carry them. From the pictures attached, the length of one side is 7/16" I don't know if you have this part, but I appreciate all help. ... (cont.)

Only marking is 24-5 FE5 CMC 75. Metal channel is 25 inches long, .5 wide. Head and foot at 1 inch by .5 inch.

Arms are 9.5" extended Rollers are .5" at the flange, .375" inside diameter. Holes are 3 7/8" by 13/16"

Hi, just double checking that I am picking the correct parts? I think I need two s140 12lb balancers. The one in the pictures measures thickness of 9/16", width 1 5/16" and length with shoe is 4 9/16". Also wondering if my pivot bar is going to fit into the s140 shoe? This is a single hung tilt wind ... (cont.)