Viewing all customer Discussions for:

Other

Hello, I bought a home that was built in 1976. Every window is a casement window and the crank handles have R.O.W on them. The problem I'm having is the yellow plastic slide piece is deteriorating and causing closure issues. Thanks in advance.

I need a lip corner key for an extruded aluminum screen frame

I have 3 Pella entry doors that need new sweeps. They are the double kerf type and the kerfs are 5/8" apart. I see you have one with a 7/8" kerf spacing. Can I get the 5/8" spacing that I need? All doors are 36" wide.

Gears are stripped in the crank case. Hello Was wondering if you could help us find the right part to replace it? Unfortunately there's no markings or information on the window or crankcase This is a block window with crank case in bathroom This is a block window with crank case in bathroom. T ... (cont.)

The crank will push window out but not return. I bought Parts 39-083 and 39-114. Do you know how to repair the current part v taking the whole window apart?

Can you Identify this part for me?

Is this part available? The arm is 5 inches long, overall dimension is 4 3/4 inches , from the center top hole to the center bottom is 4 1/4 inches. . Body width is 5/8 inch . There is a screw hole in the center of the body to screw into the frame of the window on left side. Any help would be apprec ... (cont.)

These latches are from interior storm windows on a large set of iron entry doors. The pin that inserts into the door frame and holds the window closed has broken off on several of them. Any help would be amazing!

I mainly just need the part that is in the picture in my hand but if you must send the whole lock fitting that is ok, or if you have something like it that will work i would greatly appreciate it!

I ordered the SURFACE MOUNT HANDLE SET, 6-9/16" Product Code: 82-036 which arrived today. It works as far as sizing and mounting, but the lock is different and I figured I could still use the lock that came with the new handle. I cannot due to the clearance of the door frame. Any idea on what h ... (cont.)

looking for some Q-lon QL3012 (AQ33)

I am trying to locate the plastic/vinyl covers that go over the metal channels on a Milestone Series 2000 Single Hung Window. The plastic piece is located on the right in the picture attached.

It has 2730 stamped on the side and is 28 inches long

Sliding Patio door with 2 rollers in the bottom of the door unit. I can pull the wheels out to replace. I have several doors that don't roll smooth because the nylon wheel has either wore off on the side nub or the diameter of the wheel itself has worn too thin to stay in the wheel housing. Door ... (cont.)

Hello, I have several vinyl non tilt windows that open vertically with 2 channel balances that are not sliding smoothly (jerky/stiff especially when closing) and/or have one channel balance that appears broken. I have taken pictures of one of the windows to hopefully get some advice on how to selec ... (cont.)

I see no numbers or other markings on the parts. JPG366 shows one of our problems. the plastic part that the metal stub on the window goes into is broken on a couple of the windows. Am also wondering how to replace that sliding part on JPG366 and 373. It's in a channel that seems to be inflexibl ... (cont.)

Hi, I am looking for latch and lock parts for Marvin Window. The imprints on the window upper corner are: CIG 6.08 A083530300556 NSRG 007/246 Do you have the replacement part? Thank you so much, Henry

I need 4 pieces, 2 windows. The sash weight is 20 pounds

The standard foam strips sold at big box stores don't allow the door to close or seat properly.The door probably is 15 to 20 years old and the weather stripping appears rubbery or vinyl and hollow.If you carry anything like this,then i would be interested in the cost.Thanks,Rich

15 year old tan colored hardware trim parts & screws needed for 2 patio doors. I'm willing to purchase lock sets also. I'm a remodeling contractor.