Viewing all customer Discussions for:

Other

32-6 AG5 CMC 54 are the only markings I could find

It is in a 30 year old modular house and I can't find a name or any identification on the window or part.

Hi - about to try and sell our house, but all of the window operators are old and worn down. The crank handle has the marking OP05-1509 and I think the casement operator marking is OP05-7540-03, but I need some with the hole on the right and then some with the hole on the left.Could I get some assis ... (cont.)

Anderson sliding door 12' with three panels. Center panel is sliding. I ordered an outside handle from you but it doesn't work. It looks like the original handle (which i don't have) slid between the sliding panel and the fixed panel and hung over the glass outside. When closed the sliding door cove ... (cont.)

I am looking mainly for the black shoe at the end put I am guessing I will need to order the hole arm.Can you direct me to the correct one

I have Alenco windows. Only the bottom sash moves. I need a set of channel balance as well as a set of replacement retaining clips (the ones used to remove the lower sash). One of the clips has broken.The channel balance is marked 2720Q as shown in the attached photo. The metal part of the channel b ... (cont.)

I need to locate a part for a casement window originally manufactured by Jeldwin. It is a Truth 32062

I am looking for a Marvin window balance. Actually two. I am a contractor and I've been installing Anderson windowsfor years. I must say not a big fan of Marvin. Unfortunately they are on the house that I live in now. The balance code is 26E RB

trying to replace this door handle on a sliding glass door- the outside handle is glued and can't get it off but the photos are of the inside handle that was broken. I have measured the distance between the holes and it looks like 4 inches but I can't tell if I am doing it correctly. please help ... (cont.)

I need to purchase this lock

Replacement pin for window pin

Nami code: fet series bgd/?from/???/bfs narcissism fet-1-003

I added two photos one of the opener and the other showing the hole locations on the window. The numbers I sent in my previous email is from the old handle. When I bought new handles the holes didn't align and that's why I need the exact model number as I have now.

The attached photos show a damaged balancer for my single hung non-tilting window. The balancer metal length is 34 inches, the cross section is approximately 9/16 x 5/8. The window size is a 4'5"x6'0" window manufactured by Flesher Windows, which is now part of Eastern Architectural Systems. The ... (cont.)

We have a wooden door that has a jalousie window. The crank to open the windows no longer works. There is no part number on the current device. The length of the crank handle that needs replacement is 3 3/4". Thank you in advance for your assistance. Lynda-Lee

I have a white Cole Sewell storm door installed in the early '90s. The door is still very functional and cosmetically good. The handle is no longer functional. I have taken it apart; the cam that controls the position of the latch is completely worn and useless. I would like to replace the the entir ... (cont.)

Looking for a carefree pivot bar the window was manufactured in approximately 1997 or 98. Measurements are, from the shoe end, is three quarters of an inch to the first hole, first hole to second hole is 1 in, and total length is 2 and 1/4 in.

Operator does not work, is this the only piece I need to replace?Left Lock

Hi, I need to replace 7 Andersen sash balances. Old balance #s D5 7 27 12 70 Purchased one new balance #737, is this the correct balance to replace the old balances with? Thx, Scott

Hi, My uncle has a couple of kitchen drawers on the sliding tracks and the anchor track piece is broken. Can you help with a replacement recommendation? I found these on your website (HANGING RAIL BRACKET, 1-7/16" DEEP) but not sure if those would be the correct replacement. I have attached a couple ... (cont.)