Viewing all customer Discussions for:

Other

I ordered the SURFACE MOUNT HANDLE SET, 6-9/16" Product Code: 82-036 which arrived today. It works as far as sizing and mounting, but the lock is different and I figured I could still use the lock that came with the new handle. I cannot due to the clearance of the door frame. Any idea on what h ... (cont.)

looking for some Q-lon QL3012 (AQ33)

I am trying to locate the plastic/vinyl covers that go over the metal channels on a Milestone Series 2000 Single Hung Window. The plastic piece is located on the right in the picture attached.

It has 2730 stamped on the side and is 28 inches long

Sliding Patio door with 2 rollers in the bottom of the door unit. I can pull the wheels out to replace. I have several doors that don't roll smooth because the nylon wheel has either wore off on the side nub or the diameter of the wheel itself has worn too thin to stay in the wheel housing. Door ... (cont.)

Hello, I have several vinyl non tilt windows that open vertically with 2 channel balances that are not sliding smoothly (jerky/stiff especially when closing) and/or have one channel balance that appears broken. I have taken pictures of one of the windows to hopefully get some advice on how to selec ... (cont.)

I see no numbers or other markings on the parts. JPG366 shows one of our problems. the plastic part that the metal stub on the window goes into is broken on a couple of the windows. Am also wondering how to replace that sliding part on JPG366 and 373. It's in a channel that seems to be inflexibl ... (cont.)

Hi, I am looking for latch and lock parts for Marvin Window. The imprints on the window upper corner are: CIG 6.08 A083530300556 NSRG 007/246 Do you have the replacement part? Thank you so much, Henry

I need 4 pieces, 2 windows. The sash weight is 20 pounds

The standard foam strips sold at big box stores don't allow the door to close or seat properly.The door probably is 15 to 20 years old and the weather stripping appears rubbery or vinyl and hollow.If you carry anything like this,then i would be interested in the cost.Thanks,Rich

15 year old tan colored hardware trim parts & screws needed for 2 patio doors. I'm willing to purchase lock sets also. I'm a remodeling contractor.

Looking out window. Its the right side top hinge. NAMI NFRC 100/200 CODE HII-1 RATING NFRC SERIES CLCASE MST 2650 NFRC HII-1-006-7/ 14-15 97-M

I have bifold door that came out of a closet in our bathroom. It was removed a while ago and was not the one that removed it. I installed the door in another room but don't know how it is suppose to be assembled. The part I am trying to figure out is the top pocket socket part 23-307. When I t ... (cont.)

Hello, I need some replacements. Please see photos. Thanks, Marcus

HiI am looking to buy a pair of balancer for my windows. And 4 take out clip Code: 16-002The stamp show 27 3. When I measure the length metal to metal it about about 27 3/4. Let me know if u need any other pictures. Thank you Sean

Would you have an operator similar to the attached drawing? I would need a right and a left.

no markings on lock- not sure window brand top mounted not recessed rounded corners on one end 2" screw holes 2 15/16 long 11/16 wide Can an universal latch work? can replacement e wider as long as screw holes match up?

I'm looking for a replacement vinyl sweep for my shower door. Drip tray and sweep are shown in the attached photos.

I am looking to replace several channel balances and attachments in my apartment. As you can see in the attached pictures, the length of the channel balance is about 32", and the width is a little over .5". One of the balances is stamped 31-3 Caldwell JL, and the other is stamped 31-4 Caldwell CM. ... (cont.)

Do you have a replacement for this part?