Viewing all customer Discussions for:

Other

I have a Hurd casement crank out window. The small stainless guide on the end of the bracket on the bottom of the window will not stay in the track. Hence the window can not be opened it comes right out of the track. Any suggestions?

We suspect that these original balances were too weak to work properly. All the houses in our development used the same identical window, except ours. We have double pane glass, but we suspect the contractor used the same balances as for the lighter windows. That's why I included the actual weig ... (cont.)

Hi, I would like a quote for an S795-32C channel balance with a top hook and a 15-194 shoe. Quantity of 4. Thanks

Dear Swisco, I need to replace my Window Operator on my Florida Awning Windows in my Florida Room. The only Operator that is fairly close to mine is the 39-350My operator's arm though is off set and has a threaded piece at the end of the arm that slide into the hole in the shoulder and a nut to ... (cont.)

I need two Channel Balances as pictured above. The metal portion is 13 5/8" long and I believe you can see the and clips. The width of the channel is 1/2" and the depth is 5/8" This is from a single hung window

One of the gears on the open and close mechanism is broken.

Good day,I need to replace this bifold door upper pivot pin bracket (the securing screw gets loose and causes the door to drop). The door is in a house built ~1980, and the item has an "Acme" marking in it. I included a picture of the rail width, which appears is 1/2".I have no other manufacturer ... (cont.)

I am looking for Andersen window glazing as shown in the attached image.

Please see the attached pictures. I cannot get the shoe out without breaking the metal post on that rest in the shoe. The picture above of the balance support has a number of H65 34/5M and the coil I think has a 10 with a J underneath. We believe the shoe is A1-87598.

I order last year from you. I believe it is a 3/4" offset, wheel is 7/8 ". I need to order qty 24. But I'm u able to find them on your site. Would you be so kind and assist me in my endeavors

Any help with these would be greatly appreciated.

Hi, I'm looking for a replacement piece for this black plastic piece that screws into the top of the channel of our window. It seems to be the piece that keeps the channel balance from going beyond the top of the window. Thank you! Vickie

Hi, Both drawer rail sockets have broken, but I can't find the part matching the dimensions and the whole pattern. The part number on it is 931.000.36. It is about 4 inches long. I appreciate any help you can provide. Thanks, Jun

Can you plse help me, I cannot find the part that goes on the top-ends of the Window Sash , the plastic Clips that have a holding function. they Sun-worn, broken & even lost. I cannot find them/locate them in Accessory lists for ordering them.Danke

Sirs: I am trying to get six 14& 1/4th inch side mounted balances for my Peachtree Windows that were installed in the 1980 s. Approx. window size is 34X16 inches. Windows do not seem very heavy. I did send an email but now am giving you pictures. Thank you for your help. - Peter. Also looking ... (cont.)

Hi, I need to replace a channel balance in a vinyl window in my house. The house was built in 2006, and the block and tackle balance was original and has never been replaced before. The following is etched into the channel BSI 31 5 pj I may be wrong, but from this, I figure that I need to purchase ... (cont.)

Need replacement for this balancer. I don't think they are the original Milgard balancers. Metal channel is 27" long and the plastic ends are as in the photos. The window sash weighs ~19 pounds. Please advise. Thanks.

OK- I need to try this again. I thought I ordered the correct part without sending you pictures but I did not. Let's try again. The metal channel is 27 inches long and the ends are as shown in the photos. The metal channel is stamped 2620. I ordered S370-27 but the ends are not as shown in these p ... (cont.)

The length of the metal part is 18"

Sorry there were no visible marking on the plastic piece.