Viewing all customer Discussions for:

Other

Hello, I removed this bubble seal from our vinyl tilt sash window. The window is roughly 35 years old and I believe the company name was Vekaplast. We are in the process of replacing the pile weatherstripping and several balance rods. We have roughly 30 windows in total to evaluate. Any help identi ... (cont.)

Andersen operator will open the window a crack but then makes a popping sound and hops the gear and will not engage to open any further. I have a video I can share, but it will not let me upload a video. Only numbers I found: Arm - CW35,4,5,6,SPLT Crank case cover - 7191A-33 Thank you! ... (cont.)

I need to replace four of these, so I need to know what is the item number where to buy them also, I need instructions on how to take the lower sash out and installation of the balance. Thank you, Andy

Hi,I own the attached window. Opened it over the weekend and the counterbalance flew off. I followed instructions online but the counterbalance will not support the weight of the window. I was hoping to purchase both counterbalance side (left and right) along with the slot the window ties into an ... (cont.)

Hi I am looking for a replacement for this latch. Please see photos attached. Please call with any questions. Thanks! -Josh

good morning, I am looking for a part for my window. it is the bracket the attaches to the bottom of a casement sash. I have attached photos showing dimensions thank you,

I have a very large tilt-in window (41" wide, 64" tall). I'm looking to replace all 4 balances & sliders (hope I have the terms correct). The 1st pic is what I'm calling the "slider". All 4 of these are about 1" wide, and 2" tall. I'd also appreciate any advice on how to remove them, as they appea ... (cont.)

Hello looking for replacement for lock mechanism for this.

Issue: Broken Spring-Hooks Location: On the leading edge of the divider just behind where the user pulls/pushes it to open/close. Description: The above-mentioned spring hooks are approximately 3/16" in diameter,2 to 2.5" in length, tightly wound, and have a very small hook on the end. The springs ... (cont.)

Hello, Could you please assist in silver line tilt block and tackle balance part replacement (Total of 2) if they are available and how much will it cost to deliver to Charlotte, NC. Please find attached photos for your reference. Thank you,Hussam

We manage a bunch of properties with these windows. We need the metal parts that hold the window in place as well as any other repair parts including the springs.

The window measures 33 1/2" wide X 22 1/2" tall X 1 3/4" deep The portion of the hinge that goes against the frame is 12 1/4" the portion that goes against the window is 8 3/4".

Hi, I am looking for right and left Window Clip Replacement on a double hung window.

I have two sliding glass doors that are made by Pella, I believe. They are 25+ years old, and I can't find any part numbers on them. I'm in need of the mounting hardware that is shown in photos 8543 and 8545, for the between the glass blinds. Also, in 8539, there is a cleat for tying off the line ... (cont.)

need model number to order ......21" long - 1/2" wide.

I cant find this latch for my screens.

I am looking for the bottom window seal of a Certainteed Bryn Mawr II window circa 2007 manufactured by MI windows in PA They slide in a track just like the pile weatherstrip (58-127). They move in the slot - but the window is not removable - I don't know how I can get to the edge to slide a new ... (cont.)

Dear Customer Service: I am in need of replacement roller for a four section sliding garage door screen. Do you have these or do you know where I can obtain them.? Thank you. I purchased window balances from your company and they were perfect.

I'm repairing an existing screen and would like a brace for the middle of the unit.

piece is .20 in thickness no markings on screen frame or windows