Viewing all customer Discussions for:

Other

Length 36" Stamp: 35 4 B.S.I 4 channel's needed

This is a 1965 door. So I am guessing they don't make this hinge anymore. Can you recommend some hinge that I can retrofit ? Thanks for the help. When standing outside, the lock is on the left side and you push the door in and to the right to open it.

Window belt 2nd photo 1st photo is showing handle for type of window

The handle doesn't spring back and doesn't click closed. Is there a spring I can replace or do I need a new handle? Thank you

Anderson storm door internal door latch broke off. need to replace with a Mortise Latch? photos attached

Hi,I'm looking for a couple of Roller Assembly with 1-1/4-Inch Steel Ball Bearing with the following dimensions:widths: 16mm or 5/8";height: 32mm or 1 17/64";length: 118mm or 4 11/16";Please, see the pictures with more details.Thanks, Alex

I am looking for the plastic snap in strips that border the glass on the outside ofAlenco windows. I have attached a picture. The part I need is the one with the small hole in it.

I want to replace (2) channel balancers. Length is 28 inches, 2740. Images attached. I also need the clips that are in the sash which the balancers connect to.

Please see bracket in bottom center of uploaded photo. The bracket I need is for a window that is hinged on the opposite side of the one shown in the uploaded photo. The short arm (the arm without the wheel) of a 39-334 casement window operator attaches to this bracket. Please provide me with th ... (cont.)

I have a slider with a bad roller. Here is the old one. It has a 138 stamped on it. The entire bottom of the slider comes out at the bottom and the roller assemblies are removed from the sides of the piece. Here are some pics. What new rollers should I get?

my old balance has markings 29-5 AA CMC 11, end to end metal channel is 30". when choosing weight is it critical? i think it is a 2920 or a 2930?

I would like to replace the entire coil balance system including the locking pins in a number of Prism windows. Can you tell me the part numbers I need to purchase. I will eventually replace 15-20 windows but for now I want to test replacing 2 windows first.Please feel free to contact me via email o ... (cont.)

Hi there, I'm trying to replace a number of bad coil balance shoes and pivot bars on my Alside Series i201 double hung windows. The bars are approximately 2 1/4" long, and the shoes are approximately 1 1/2" x 1 3/8" x 5/8". The coils seem to be fine, it's just the shoes that keep breaking. Thank ... (cont.)

I'm looking to replace several of the part in the picture. Can you tell me what is the correct part to order. If you are able to tell me all of the parts required to maintain these windows, that would be great and I'll order several of each.

Hello, I am looking for 3 Extended travel balances measuring 27.5" (metal only). There are no stamps on the balances. I believe they were manufactured by Certainteed. Thankyou, Jason

My door is an Emco serial number 5749512. It is 1 1/2 in. thick. I need the mortise latch and a set of handles that will all fit together. I prefer a black finish, or nickel if black is not available.

I need replacement brackets for 2 draws. Labeled.R-40-28

Gold sticker on window says: MFR CODE CERTAINTEED AUBURN WA (11-1) or (H-1) Stamp looks like it reads 25 4 BSI I will need two balances, please. I have purchased from Swisco before.

Hi. I purchased 7/16" nylon wheels with pins from you for my older aluminum sliding windows. I removed one of the old wheels and put the new wheel in its place. The wheel fits and the hole for the pin lines up, but the pin is too large for the existing holes. The holes in the aluminum frame are ver ... (cont.)