Viewing all customer Discussions for:

Other

Hi,We have seven casement windows and they were installed in a construction project building in 1983. The mechanism work drives on three windows are stripped and they cannot be used to easily open and close the windows. We are hopeful that this "Left hand" Anderson mechanism can be identified and I ... (cont.)

looking for weatherstrip for pella hinger patio door approximately 35 yrs old.emporia

Hello.....I have a few windows I want to fix, this is the first one 15 inches long 1/2 wide.....20 years old

So i believe i have the 2900 series windows in our home. We purchased it in 2014, but was built in 2007/2008. I have a couple of windows that have broken shoes and need to get some of those. The balances appear to be okay, but the shoes are plastic and the track appears to be 1-1/4". Also, the top t ... (cont.)

this is a 4 & 15/16ths CC sliding door handle from New Zealand with thumb lever ( not shown ). Need to replace. Do not see any branding except maybe MM ? WW? Please help.

I need a replacement latch. Sticker says: - American Window and Door - DSL20 - 11872 Kosa - 624090.060 - 9/30/09 ES301D

It is part of the closing mechanism.

Hello I have some missing window rollers and have provided an image of one that is installed. It looks to be an insertable roller. Might you carry this?

We have two different balancers for two different sized windows. One is marked 2020 and has about a 21" metal channel. The other is marked 2620 and has about a 27" metal cannel. All the other hardware is the same between the two and are represented in the photos. We need about 8-10 of the 2020 and ... (cont.)

I have pro shield casement windows from weather shield that I am needing to replace.

Searching for 1 plastic roller for aluminum window. It appears to snap in small hole on the outside of the frame. House built in 1961 California.

Looking for the correct part number for a mortise lock mechanism for a Pella 750 series slide glass door. Is it 82-247? I can't believe this part is almost $200 but I want to make sure I buy the right part. Please advise.

I am searching for what I believe to be a drawer track back plate. The one in the picture was manufactured by Ronthor NYC. The square is 15/16" to the exterior edge of the square. I suspect the top which screws or staples into the back of the cabinet is another inch but as you can see the plastic ... (cont.)

I'm looking for screws to fit my nami windows. Can you help. Dave. Thanks

Hello, I am going to order Oil Rubbed Bronze Atrium Door Lever Lockset Product Code: 82-398, but would like to use the same key at least with 5 of the 6 that I need to order. Is that possible?

Hi Swisco - i'm unsure of which pivot bar to buy for this window. As you can see there is a lot of rust and the current pivot bar has basically disintegrated and some parts are inside the lower portion of the window. Do you have enough information here to determine the part? Other parts i am orderi ... (cont.)

Hello - I am in need of a replacement surface mounted tilt latch in tan. I don't see a similar product on your website, even in a different color. Note this is the left side and it has a "night latch" pin to secure the window while open. Thank you.

I'm a return customer and have another broken balancer and shoe that needs to be replaced. I need both sides for the window. I will send photos and info for the window. Thanks!

Hi, I have a number of different window sizes that need these parts replaced. I don't know their make or model. Could you let me know what other information you need so I can order them. I hope that the 2 pics I've enclosed help. Many thanks, Ian

Hi all, Hoping to confirm a part number for 6 left hand replacements. Hole spacing is 1 1/8 x 5.25 with a 2 3/8 arm. Some of the arm attachments seem to be via c-clip and others by threaded grommet. Also looking for an extended or straight crank handle. One was installed in a corner beside a door ... (cont.)