Viewing all customer Discussions for:

Other

Not sure which side of window this goes on, but looking for the opposite for the other side. I need both pieces and possibly the screws to mount them both as I have none. Please and thank you.

I had carpet and now have refinished the hardwood floors that was underneath. It looks great. The closet door hardware is probably 70 years old and the 2 separate old floor guides already sat on an ugly extra little piece of wood about 5.8' thick which they had carpeted over. Now there is going to b ... (cont.)

I'm looking for a replacement for my white 28" channel balance. It has a 2800 BL stamped on it, I think I found a similar one (28" Series 770 Balance - Product Code: S770-28), but that one looks silver, is that part available in white?Thank you,Mike

Need two replacement balance springs Length of metal portion of balance spring is approximately 32 1/2" Width is 1/2"

I purchased replacement thermal guard locks from you. However, I cannot get the old ones off. Is there something else besides the screw I need to do?

Looking for that part (pivot bar). Can't find manufacturer of window. See pics

I am trying to find replacement latches. There are two moving latches in this one part. The latch on the bottom or foreground releases the window from the frame and the window will tilt in to the room. The top latch is what you slide to raise and lower the window. I was unable to find a name or ... (cont.)

I have a old mobile home that has alum frame windows that needs hareware plastic parts can you help me.

The thumb latch broke on our patio door. The patio door has double mortise latch with an anti-slam button, the bolts for the handles are offset at 3-15/16 inches and the thumb lever sets an inch above the bottom bolt. The door and trim is white. Would the thumb latch replacement part 82-107 work wi ... (cont.)

Hello,I need the lock catch for the New Castle XT /Insulate 960.We removed the dog door and we can not find the door catch that the lock goes into.The lock is a three prong with the top and bottom catching inside and the middle one is a press in button of sorts that allows the upper and lower to rel ... (cont.)

Hello , This is Bill with Arizona Hardware , I have an old Imperial Keynetic pull with backset # 5820.170 and keeper I need to replace , the finish in satin nickel .I would like to get as close as possible in style and color it can be keyed or a patio function . It looks like the 82-030 & 82-2 ... (cont.)

Looking for clips for Phillips storm window Which holds the 2 pieces of storm window together

I believe the 39-253LB would the correct replacement part. Just want to confirm.

Needing the piece in first picture I believe it is a guide. Need part in second picture on left.

Hello, could you give me an idea what parts are available in your stock to replace bottom track and rollers of sliding doors. Thank you in advance. Regards. Victor

Problem: The plastic mounting brackets for the casement window multi-point sliding locking bar are breaking (20 yrs old) Desired Solution: Replace multi-point locking bar and mounts Data: Lock Rail 39" x 1/2" 5 brackets per rail Bracket 3-3/8" x 7/8"; 2-Mounting screws 3" center

ItemReturning: Item 84-152 Item 59-054ReasonForReturning: Item 84-152 wheel was too small. There is no description on your site as to the width of the wheel. Everything else on the roller matched what we have. You should add the width of the wheel on your site. It doesn?t saddle 1/4? track. These ar ... (cont.)

Hi, I have an installed 1989 Great Lakes Window (bow) with two casement window on each end. The left casement window, the window can open with the handle but won't close it with the handle. It looks like the operator part that connects to the handle is stripped. I found serial numbers on operator ... (cont.)

Good Moring I'm trying to figure out what part I need for a window repair. Can you help me please. thank you.

The weather seal shown is from a wooden Pozzi casement window circa 1980. Dimension of side with return that fits into a slot in the wood frame is just over 1/4". The dimension of the bottom , sealing portion, is 7/16". It is a plastic material that has become brittle over the years. Can you pro ... (cont.)