Viewing all customer Discussions for:

39-107 Truth Hardware Operator Cover

Window crank

Please see the attached photos. I'm looking for the Truth 24-45054 light beige round opening with tightening screw. Your part 39-114L Truth 21-45240 spline is too shallow and has wings. Thank you for your help! Dan Stack

Hi, I'm attempting to replace the hinge pictured. I purchased 39-155 but the pivoting length of the upper arm was too short. Everything else seemed to be the same

I need the plastic cover for the crank and the two brackets that the locking mechanism attaches to , to lock the window.Attn :KathleenI just spoke to her

Hello, I have Pozzi windows that are 25 years old. I need to replace several of the crank mechanisms and want to make sure I order the correct ones. The picture of my window looking at the window from inside the house I would imagine it would be a left side crank. Yet the part photo attached has a ... (cont.)

We recently purchased a home that needs some window replacement parts. After perusing your website, however, I couldn?t tell what parts would match. Could you advise, please? Representative pictures are attached. Thank you,

I'm in search of the crank mechanism and arms for a Vetter casement window. The teeth on the drive gear are stripped. Hoping you can help.Thanks,Roger

I have a lot of crank windows that are no longer working and the entire mechanism needs to be replaced. I ordered a 39-035 and 39-036 to test in one area. Everything fits except the bracket that connects to the window. The new ones are two inches shorter and will not fully close the window. Is t ... (cont.)

Hi, am looking to replace the broken casing(and probably handle) on my casement window. I think it is a Milgard window and am attaching pics of it and its sticker. Any assustance would be greatly appreciated. Thanks, William

I am looking for replacement parts

The following is the info I can see Long arm 30470LH Short arm L3084 Short arm extension 20756 Name of unit truth Entryguard

When I attempt to close window I end up with the handle and handle cover in my hand. It opens fine. Casement operator says Entry Gard Truth. Numbers on closer includes 20810 and 31538A. Can I just adjust it or do I need a new part. The handle cover is slightly cracked, but I don't need a new one ... (cont.)

The long arm is 9", the short arm is 4 3/8. Says Truth Entry Gard and has a number that looks like 31538, but I can't be sure. I won a glass shop in CA and have ordered from you before. This is in a customer's window, so I can't take it out until we win the job. Thanks, Laurel

Need replacement parts. I removed a Truth 2 arm casement crank operator. Long arm has "Entry Gard" & heel to end 9 1/4". On top of crank plate 40254. Short arm 20544, Short arm 20544 lenght to bended connector 4 3/8". Bended short arm base 30630LH. Need Right hand and left hand. Name of c ... (cont.)

Thank you for offering this service! If you have this part and also the LH version, we will need to order several.

Hi, please find enclosed photos. I need the entire operator. Thank you Joe

Hello - This single arm operator had the worm gear push out. I cannot find a similar single arm operator anywhere. DO YOU HAVE THE EXACT REPLACEMENT PART OR ONLY SOMETHING CLOSE? It looks exactly like the image posted back in august 12, 2014 in which Tom from SWISCO responded: "August 12, 2014 I ... (cont.)

The big arm says "Entry Gard Truth" on it. Small arm has #20810 on it. Measurements appear to match. I'm thinking this will work with Swisco Product code 39-032. Is that correct?

I have a window in need of a new crank, about 25 yr. Old house. Number on the back of the arm is 40530 and number on the plate is 45047. Pivot point to middle of roller 9 3/8, plate is 4 3/4 by 1 1/4.Can you help me find this? Please and thank you.Njal

I need all 3 parts.