Viewing all customer Discussions for:

39-227B T-Crank Handle, 3/8" Spline for Pella

Hi there - I'm wondering if I can replace my Pella awning-style window cranks (see photo) with low-profile Pella window cranks. Do you know what part numbers would be compatible with the existing cranks, and, if possible, a lower-profile version? Thank you! Katie

Looking to swap out old cranks on Pella series windows. Looking for something compatible with the photos below.

I am trying to replace a white folding window crank handle marked Truth with a Pella knob. Looks to me to be 11 tooth for a deep spline, I measured it and believe out to be 3/8" bore. I may not be correct but I have included several pictures. Can you help me make sure I am looking for the right h ... (cont.)

Would like the T crank that fits this Pella window in champagne. 34 neededRequested on please notify when in stock. Want to make sure this is the correct part 3/8 size Thank you Patti

Hello Gentlemen-We are looking to replace a crankset operating box and wing handle from a vintage Pella casement window. The unit is single glazed with a storm panel.It is a left hand swing as viewed from the interior.The existing crankset has a sheared off handle post.Mark

I installed a new toilet and the tank, which is under the window, is taller than the old one, so the crank on the window hits it and can only make a half turn. I'm looking for a shorter or collapsible handle and champagne color.

Hello. I'm wondering if: 1) the cranks in my my older (some are as old as 1988) Pella windows (see pics) can be replaced with a folding crank like my newer Pella windows. 2) or is my only option the t-crank handle? 3) is the t-crank handle a lot less functional than the large handle? i.e., do ... (cont.)

I am looking to get a brown pella crank set needed asap. Help! I attached the picture to help. thanks, Brett

Would to find white color knobes to replace old bronze knobes. I've had no luck online finding parts. I would very much appreciate your help with a good replacement part.

I'm looking for a Window Crank Handle that might match the one in the picture? It appears to be a "3/8" in a champagne color. Any ideas? Thank you!!! Gloria

I need 11 small T cranks to accommodate window blinds, existing arm has 12 points. Can you give me availability and price.

I was wondering if this crank can be replaced by a folding crank? I would like to get plantation shutters and the cranks get in the way of operation. Thanks

I purchased Part 39-205 to replace a "Truth" part that fit a Pella Window Casing (attached photos "Pella Truth a and c" are photos of the part I have, and desire a replacement for) The 39-205 that I received has a round interior that does not fit over the "geared" window casing part (attached pho ... (cont.)

Hi! We have Pella windows from 1976. Are these t cranks correct for replacing the original cranks? I'm wanting to make room for blinds.

I ordered and received 6 Pella T-crank handles 3/8". 39-227B. The cranks are too short. I think I need a 5/8 ". What do you advise? I couldn't find one in your catalog. Nick

My current cranks are Pellas stamped with 7138 and x429. I went to my local hardware store and purchased t cranks that don't work. Do you sell T cranks that will fit my windows?

Our Pella windows were installed in 1991. We need to switch the handle from the traditional crank to a T-handle. Our Pella tech told me that the our handles are 11 (12 to be exact) splines and 5/16

Our recently purchased home was built in 1971 and has the original Pella casement windows. The cranks all seem to be stripped and I can't seem to find working replacements. The part number on the crank is X-429. Ideally we would be able to get "T" cranks so that we can close our plantation shutte ... (cont.)

I have Pella Casement Windows 3/8" splined. Do you have anything that will work?

What is the material your 39-227 pella t-crank handle is made of? It looks like plasticc.