Viewing all customer Discussions for:

15-150D 1/2" Coil Double Support

I need to identify all the components, including the spring assembly, the locking mechanism, and the side pins on the sash. The locking mechanism has a number of 4.610.108 on it.

I'm looking to find replacement parts for the coil balances and pivot shoes for several windows in my house. The one pictured had coils marked with 5 lb and 6 lb weights. The cartridge holding the coils is approximately 1 19/32" tall, 1 5/32" wide, and 9/16" deep. The pivot shoe assembly is approxim ... (cont.)

Hi, my double hang window spring coils of constant force window balance broken and can not stay opening, I make a list of order to make a replacement, is this list are suitable set that I need? Is there need to order left size and right side different parts? Thank you

12 windows need replacement partsJames

I believe I need a new coil balance for my window. I attached two pictures. The first one is a part (part # 801020) that would work, but is too tall. It is approx 4.5 inches tall. The second picture is the part that is broken that I need to replace. The part # is partially broken off, but en ... (cont.)

Looking for help in ordering the right window spring and sash retainer pin. Thank you in advance! TW

Good afternoon, I have this balance spring system from an older window. I was wondering if you could help me source either the entire set-up or each part to assemble here. I would prefer the least amount of assembly. Thank you in advance and have a nice day. Kailey

I am looking for 3 different parts. I think they are called 1. coil balance shoe 2.window double coil balance system 3. tilt window latch. Its the pieces in picture 4, 5 & 6. I do have the loose parts that we took out of the window if you need the actual pieces. I attached a picture of the only ... (cont.)

Need 1/2 INCH BALANCE and PIVOT Bar for Simonton Window 4141011/02 (35.5 x 59.5 -PFSH LEAR F 0031

The existing housing has become brittle has started to fall part (It has on at least 2 windows). This is my first repair. I replaced the coil springs and housing. The issue is the new housing is a box. If I move the window up or down pass the new housing, I will break off the tabs on the tilt win ... (cont.)

Hi there I am searching for sash coil and plastic frame housing, double on each side of Window Stamp on existing coil is 9 Don't know my window manufacturer but windows installed over 15 years ago Will also need pivot bar Do you have the parts?

need help identifying for this part.

I am looking for replacement Pivot Lock Shoes as one is completely broken, Coil balance and coil support. Can you identify, based on my photos, what replacement part numbers I need? I think I need 15-111 Pivot Lock Shoe. Mine is 1" tall, 1 1/2" wide and @ 1/2" deep. (See attached photo) I think ... (cont.)

I have a broken double coil support that looks very much like your #15-150D except that the top is curved and it is 3-3/16" long (yours is 2-9/16" long. I'm told that my window is a Simonton. Is there a way to tell difinitivly what brand it is.

As per my chat with a Swisco help desk rep, this am, attached are pictures of the window parts I need. There are two pictures of each part. One is totally broke, the other seriously cracked. I need one for the left hand and one for the right hand side. Please let me know if you have them or someth ... (cont.)

The only identifier, after removing the hardware, is #5.5 37 inchs PAT 5232208 on the coil. I need all the proper hardware to replace all coil balances on both sides of the window, the pivot shoes, and coil supports. not sure if this setup is considered single coil, double coil, or more. Note that ... (cont.)

Hello, Could you please assist in silver line tilt block and tackle balance part replacement (Total of 2) if they are available and how much will it cost to deliver to Charlotte, NC. Please find attached photos for your reference. Thank you,Hussam

Hi. This is my window balancer. So I don't now what kind I need . Thanks . D.

Looking for replacement coil balance for the above described window

The only identifiers I can make out on the springs are #4.5 35" on one spring and P 5232208 on another. I dont know if they should be all the same. The springs are both 1/2" wide and the shoes are 1 1/4" wide by 1 1/2# long. There are no markings on the pivot bars. If this makes sense to you guys, I ... (cont.)