Viewing all customer Discussions for:

82-037 Andersen Reachout Deadlock Assembly, 2-Panel

would you please advise what part do I need to repair the lock on these pictures. it stopped locking my gliding door, Thanks a lot! Alex G

I have attached 2 photos of myu sliding door lock. I am missing the keeper and unsure which one I need so I can replace it. Thank You

I need replacement parts for the inside of my Andersen door handle. See attached images.

Door wall lock and lock plate. Andersen gliding door installed 1995

I have an old, possibly installed in early 90's Anderson vinyl sliding glass door with need to replace lock assembly. The pin in the receiver in no longer locked to the center. from your diagrams it is 2562123 and replacement is the 82-037, 5 1/2 inch length receiver. But I would also would like to ... (cont.)

Hi, I'm looking for a replacement lock set for An Andersen Sliding Door PS11 6R Oper. It is a 2 panel door and was installed in 10/82. Can you help?

I am looking for a replacement for locking hardware from my Andersen Window glider door (vinyl inside). When I took the part off, it had a few numbers including 7700-14 and 2573558. Can you suggest a replacement?

7442-3 is on the inside of the latch I think i the door was installed in 1998. Thank you.

I need to replace this sliding glass door with a new thumb latch and reach out lock. I am not sure what type to order. The latch has 2 holes, 4" apart. The lock has 3 holes, the top and middle are spaced 2" apart, the middle and bottom are spaced 2 1/2" apart. Any input would be appreciated. Than ... (cont.)

I have 2 of these Andersen sliding doors, circa 1983. The inside mechanism will not turn to lock the door. A friend removed the lock and it is frozen. Do you have replacement parts?

Hi... I recently bought the Andersen Tribeca Thumb Latch Replacement Product Code: 82-043 - I installed the thumb latch and discovered the catch/receiver was just a flimsy strike plate and wasn't adequate for properly locking the door -- there was no original receiver in the door jamb when home w ... (cont.)

The broken latch has "C-7442-5" molded on its' underside. The door handle screws are 2.5" measured center to center. Hope you can identify the replacement part based on these photos and description. Thanks Ralph

Anderson window circa 1993- thumb snapped off sliding door. Need replacement part. Does anyone know what part number I need?

3 of the 4 1 3/4" screws that hold each of the units (lock and receiver) into the doors are stripped. i.e. I need those also. the lock unit is going to have to have the screw cut to get it out so I can't do that until I have a replacement. I am sure it is the same size as the receiver, which is 5 ... (cont.)

In Sept 1998 I bought an Andersen Sliding Glass Door model FWG100068-4. The thumb lock is loose - can that be tightened or do I need to replace the thumblock and/or the entire latch assembly? Pictures attached. I think it is a Newbury style thumb lock but not sure? Any help is appreciated Stev ... (cont.)

Please find pictures attached of thumb lock to be replaced. From the top of the thumb plate, picture 1 & 2, it is 3". From screw to screw it is 2 1/2". Numbers on back of thumb plate, see picture are, S2573553 & W2574554. Numbers on lock set are 2573558 & 7700-14, see picture I have ordered ... (cont.)

need thumb lock as well as internal locking mechanism

Hi, Could you look at the images I uploaded and tell me if you make a keyed lock I could install on exterior of door that either works with existing interior latch, or I could replace both? The door closes to the left when looking at it from the outside. Thanks Jared

Looking for a replacement mortise latch for Andersen Sliding Glass Door vintage 1998 +/-

I am need of a new mortise assembly?, the part installed in the door, (pictures 1, 2, &3) for an Andersen PermaGlide door. The numbers visible on the assembly are: 2573558 right below the Andersen logo, and 7700-14 further down. The part measures 4-1/2" long, 5/8" thick, and 1-5/8" deep. I should ... (cont.)