Viewing all customer Discussions for:

82-218 Mortise Lock, Round Face, 3-11/16"

I need this lock for door sgd-r20-96x96,series 8670/series Help!!!!!!!!!!!! Dave

I am looking for a replacement lock for a sliding patio door. It is an inner lock and the measurements of the opening are 80 mm long and 13 mm wide with a rounded face. The distance between the centers of the two screw holes is 92 mm as best I can measure. The original lock fell into the door frame ... (cont.)

Ca you help me find this mortis lock please

Hi my wife & I recently purchased a home & The previous owner installed a doggy door onto the rear sliding door. They didn't give us the original lock that attaches to the door frame at the wall. The sticker on the wall says Series AV 450 - SGD R20 99X95. Do you know what part we need to get to repl ... (cont.)

About 4"center to center. K and k. Patented 1973 Screws about 2 5/16" long. Handle length 9".

This Is For A Heavy Sliding Glass Door At A Daytona Beach Beachfront Condo (Possibly A Storm Door To Protect From Hurricanes) Lock Is Broken. I Need Handle, Mortise Lock, And Keeper Stamp On The Track Says "AAA Aluminum Stamping Inc." Its White Outside With A Wood Indoor Handle

Good Morning. We are trying to replace a broken handle on our sliding glass door because the lock is broken. Please see attached the best images I could take. Here is the info on the door: PPG Herculite K Ansi Z-97 1-1972 3/16" U Tempered Safety Glass and over to the right hand side i ... (cont.)

I have a sliding glass door in my house with a broken lock. The sticker on the door has NAMI code s-019-1 (says something else but its ripped off) rating sgd-r30 (the rest is ripped off and unreadable) series 5500 mst 8068 ( again ripped off) Its a White Handle/Door. Do

I have a Pella sliding glass door that is missing the strike plate. Here are two pictures - the lock recessed in the door and the holes in the door frame for the strike plate. can you tell which strike plate I need from these photos? eric sacknoff

We bought a house that is missing the sliding glass door hardware and lock. I can't find the manufacturer of the door. I looked at Lowe's but can't find one that looks like it would fit. I have attached 2 pics of the door and a pic of the lock clasp or what it attaches to. I think it's the 3 an ... (cont.)

I am searching for the locking mechanism for my patio door. I believe this door was originally made by Florida Extruding since my windows were. This is a non-keyed mechanism (cannot open from outside when locked). Do you have this mechanism available. Thank you

I need to replace the mechanism that's in the photos I've sent. The only markings on the mechanism is "SC". The inside of the handle is 1060-1943. Any assistance would be most appreciated! Thanks! Alan Percival

I ordered and received Mortise lock, square face, 3-11/16" part no. 82-223. I had to lightly file the face that fits through the hole in the edge of the patio door to make it fit properly. Having then installed it I realized that the slot in the lockset was about 45 degrees off from being a direct ... (cont.)

Could you help me find the correct mortise lock for Pella designer series sliding patio door ( 1986 model XO26CS) photo attached. It is a single point latch with no key.

Looking for these parts. Thanks, Jerry

On part # 82-218, how far out does the lock stick out prior to pulling it up into the final locking position.

Good morning, I need a latch and handles for a sliding glass door. the broken latch fell inside the sliding glass door when it was being removed. The space the latch goes in to is 1/2" wide by 3" in height, while the screw holes are 3 5/8" center-to-center. The handle mounting screws are 3 15/1 ... (cont.)

The lever on my patio door lock broke. I do not know the door manufacturer. When I tried to remove the internal lock, it fell inside the frame to the bottom! (I should have looked at your video first!) Do I need to remove the door & retrieve the lock that fell into the frame??? The opening in th ... (cont.)

Just bought an 82-218 mortise lock for an American Craftsman sliding door. Looks like the old lock, but if I use it right side up, the existing door handles can only fit in the backward position. Can I use it upside down so the latch travels downward ? Then the handles can be installed in the righ ... (cont.)

Dear Sir/Madam; I am looking for a replacement of a round face sliding door lock to replace one removed from a Sash Controls model 060-1255. Is your product 82-218 an appropriate replacement? Thank you very much for your response. Darrel