Viewing all customer Discussions for:

84-011 1" x 11/32" Corner Screen Roller Assembly, 7/8" Wheel

U get one chance to get this right. These are the screen doors rollers from the international space station. I'm sure u know that it gets hot and muggy in the station so the astronauts like to open the patio door. Currently they cant. Can u I'd these please.Cordially yours,Buz LightyearAka David ... (cont.)

My rollers are 3 3/8" high and with the wheel inline with the length it is 4 1/2" long, the width is 1" , the depth is approx 5/16", the wheel is 7/8". As you can see in the pics there are no marks or numbers. I would like to confirm that your part #84-011 will work for my door, even though your p ... (cont.)

I have screen door and have purchested roller assembly 84-011 from you in the past. The mechanisms seem to have weak spring and here in Arizona, plastic does not last well. Are there any equivalent models of that roller assembly that have stronger springs and metal rollers? Thank you Judy ... (cont.)

Am looking for 2 of these

Could find no names or part numbers. Part has spring with 3 turns around axel (left side of photo) Plastic 1 inch wheel with rivet for axel of the wheel (right side of photo). No observable screws to remove wheel assembly. 1 adjust screw on side. Have 20 screen doors like this with age ... (cont.)

I'm working on a project which included re-screening 3 sliding patio doors. One of the doors(4'x8') fell apart as I took the screen off. I salvaged 2 pieces (pictured). I can't seem to find this exact size anywhere. I'm hoping you can help. Each leg of the corner is 3" long X 1" wide X 3/8" thick ... (cont.)

are the rollers the same size on top and bottom . and is the dimention inside or outside

Attention Please, Can you please tell me if you all have the adjustment screw (sliding patio door wheel) in the attached photos? The screw I need looks very similar to your 84-502 and 84-506, though the 506 has more thread lines per inch then the one I need. The screw I need appears to be a #8 ... (cont.)

Morning, I recently ordered your # 84-137 roller assemblies. turns out these are to large. I need a 3/8 thickness instead of a 7/16. Do I need the 84-011? Please advise when you can.There are no numbers on the old rollers Thank You Darryl

How do you install the roller. Does it come with a screw or pin

Hello..what will be the max width of this roller with pin installed? I have screen that has opening of only 3/8..will this 84-017 fit? I can not have pin or screw taised bigger than total 3/8 from side to side. Thank you

I was wondering if you had a frame corner that would work with my 1984 Atrium door screen frame.

wheels on bottom of patio screen door that can be adjusted by turning a Phillips screw on the corner of the door. I can't figure out how to get to - or remove the wheels. I can see that a spring is missing from the bad wheel.

I'm hoping you have a replacement for this corner assembly for my screen door. I would need a set of two. Dimensions are provided in the attached image.

Attached is a picture of our screen door roller. The roller wheel itself is riveted to the frame. There are no marks on the roller. The screen door handle has "PGT" with the number 1805 on it.

Sir, I have 4 doors that need new rollers. Can you help me regarding removal of the old ones? I'm not certain how they should be removed or what type they are. Thank You, Richard

How do you remove the rollers from the screen door with out taken screen off.

I have an older (25 yrs) "The Atrium Door" brand screen door that has a broken nylon adjuster lever (internal to the door) and broken spring wheel. I think I found the steel wheel in the 84-006S, but I don't see a replacement adjuster assembly. From the products on your website, it looks like I ... (cont.)

Hi do you have replacements for these rollers? I can't see a screw anywhere to take them out. you can pull on them and they are attached to a flat piece of metal strip but I can't see a screw there either. they almost look welded to the strip because there's a bump of metal to connect it to ... (cont.)

I need a replacement for part # 8221 ASP It looks just like your part 84-026 but it is only 1" wide instead of 1-1/8" wide. I tried the 1-1/8" ones and they did not work.