Viewing all customer Discussions for:

21-058 Bifold Door Guide Pin, Leigh, Monarch

My bifold doors to my bedroom closet will not close unless you lift up on it. I believe I need a new top pivot pin, but I'm not sure. The closest I found on your web site was #21-058. Is this what I need or something else to make it close properly? I don't notice any cotter pins missing, but maybe ... (cont.)

Need complete set of hardware to hang. Top and bottom. Track requires tapered nylon guides to fit.

one panel is sagging and is dragging on the bottom track. Was told it needs a new pin that will raise the door and lock it in place

Need some mounting hardware as a few pins are missing and some exist but seem to have nothing holding them in place. The tracks appear to be in good order.

Hello, I need part numbers for both complete pins and brackets for bi fold doors as shown.

Trying to figure out what parts to buy for top and bottom stationary and the ones that move also need plastic parts that go into track .basically need all the parts

I'm having some trouble locating the hardware for my bi fold doors. I've checked the stuff at the big box stores and it isn't long enough to fit through both holes and I cannot find the plastic bushings that the rods go in. Perhaps you can be of some assistance thank you.

I have Leigh full vu bifold doors model S907213 (5' door) and S995806 (3' door). The track and nylon guide and spring are worn out. Can you recommend the complete replacement set for these doors that were installed in 1972. I have 3' and 5' doors. I have about 60 sets of doors that are wearing out ... (cont.)

I havre a set of bifold mirrored doors, with what appears to be 21-058 as the top guides ( only they are 4 1/4" long= complete with spring clip and guide. However the bottom guide ( not the pivot) seems to be 21-049 - ie no spring and that little nylon guide - actually two of them and it i ... (cont.)

Have unknown mfg steel doors with mirrors. parts are not the same on all doors. Need to replace a bottom pin with spring; goes into slide on bottom track. Present pin has no hole for carter pin, but all others do. Pin is 4 1/4" long and 1/4" diameter. wish to replace with one with a hole for ... (cont.)

I have 8 of these bifold doors and on some of them, the upper and lower pins need sliders. RIght now the pins have no slider guides and are metal on metal. Attached are a few pictures of what the good sliders look like (upper and lower)and a shot or two of where the guides are missing. I am in need ... (cont.)

21-050 and 21-058 look like the pivot guide pin I need for my 40 years mirrored bi-fold closet doors. The nylinder and spring also looked like what I need, but my pin is only 4 1/4 in length. Do you think the 5 1/4 would still work?

hello, the 21-014, 21-049, and 21-058 appear to be the same pin with differnt accesory parts. Am I correct? Is ther any differece as to where the hole for the cotter pin is drilled? Ie. is one part 2" from the top vs 2.5" from the top...

I have attached files of pics I took of my doors. I hope you can confirm the parts I need to order that will work. My doors have tracks on the top and bottom. I only need 1pin for the top and 1pin for the bottom. The pics I sent show that the bottom pin doesn't need to have a spring. The pin caps ar ... (cont.)

I am trying to find out if the bifold pivot on the bottom of the Full - Vu door requires a spring to push up or push down the pin that attaches to the bifold door pin cap. Where are are 21-049, 21-050 and 21-058 used, for the top or bottom of door ?? The pin that is there now thou badly ru ... (cont.)

Leigh Full-Vu metal bi-fold doors. Coopersville, Mi. I need 6 pivot pins, 6 guide pins w/ nylon caps, 10 springs, and 4 rubber stops. Thanks

The community here must have 1000's of these folding doors but our maintenence crew contends they can't find the parts. I would like to buy the parts to fix my own door and refer our people to where to get the parts. (I assume you can supply). Here are some pictures of the fittings on the doors. I w ... (cont.)

I need this part for my Bi Fold metal door but i didn't see any spring in assembly. do we need to buy the spring sprate and what about the bottom of the door do we used same assembly. My door is Leigh and part number is 8433 because i saw paper on the door. I need help to find the right part . Waiti ... (cont.)