Viewing all customer Discussions for:

21-058 Bifold Door Guide Pin, Leigh, Monarch

what do I need for bottom of my mirror door

I'm looking for the bottom pivot rod for this bifold door or suggestions for alternative fixes.

Where can I get door pins and anchora for the full-vu closet folding door?

I recently purchased a rebuild kit for ~1980s mirrored closet doors. I cannot get the pins to stay in the pin caps as the pins pull out when opening/closing the doors. I reversed the spring tension on the doors(top: push up vs pull down to engage pin) and the pins still will not seat in the cap. ... (cont.)

Bought the 21-058 pin assemblies which use the 108 plastic guides. The doors are leigh 96 inch metal bifold. All the hardware seems fine and installed ok but the 1/4 pins seem to pull out of the plastic guides when opening doors. Is there any way of keeping the pin snapped into the guide tighter. ... (cont.)

Pin hardware for 8 foot metal bifold doors. Need all hardware for 2 doors

Hello, Need replacement plastic sliders for top and bottom rails. The pin is 5 1/4 inch long, 1/4 inch wide. I would also appreciate receiving information about a full set of replacement parts (top and bottom). No idea who manufacturer was. Thank you in advance.

Need replacement bottom pins and a couple plastic sliders for the bottom rails. Pic1 shows top pivot pin (which I have all of), pic 2 shows bottom of a door, pic 3 shows the one bottom pin and the plastic slider that it snaps into. The rail is at (or just over) 7/16ths inch wide. The pin is 5 1/4 ... (cont.)

I Have a Leigh Product Bi-Fold Full-VU door and the Bottom slide broke will this 21/203 Pivot Bracket repair It? It looks like it might my house has several of these doors Here is a picture of it thanks in advance Gene

I am looking for the pin that goes into Bracket #21-205 for the top of a Leigh Bi-Fold door. 5/16" dia Solid round bar x 5 1/4" long, No head on either end. Cotter pin hole drilled 3 1/4" from one end. I need 2 pieces. Thank you. Paul Wainwright

Mom's place with metal bi fold door. Could you help identify correct part(s) needed to repair

Hi, I want to replace all hardware on 3 of these bifold doors (including top and bottom tracks). The door openings are 4' x 8 '. All of the plastic clips are worn out and the tracks are beat up.

I'm repairing some old metal bi-fold doors for a customer. A cat urinated on the doors and bottom track for years and caused major rust damage. I had to add sheet metal and angle iron to the door bottom. I'm hoping to replace the bottom track with 21-402, and pivot pin 21-002. The upper track has ... (cont.)

The pictures show a pin which you have to push up and slide into the double-u shaped plastic slide. The doors are over 25 years old. I can't find the parts in any store such as Home Depot, Lowes, Ace Hardware and an old hardware store. I havae called every bifold door place and can't find the par ... (cont.)

Hello,As you can see I have part #21-205 bracket. I am missing the pin that goes with it. Are you able to let me know what part I need? Not sure if the diagram is helpful.Thank you,Eve

Hello I am sending photos of doors that I am to repair... if possible. I would like to see if you could check the pics out and determine if you have the parts... but... mainly... look at the pic where the bottom of the door has damage and whether it is worth repairing or not. This is for an elderly ... (cont.)

It looks like I need 5 sets of the 21-049 guide pin, cap and nylon spacer(for lack of a better term). My question is this: Does the cap fit in the bottom track? If I seeing things correctly the nest logical question is how do you get the cap in the bottom track? Does it just sit in the track or ... (cont.)

Am I correct in thinking that the 21-058 pins go on both the top and bottom of the door, including the springs? The doors I'm working on are missing the hardware.(the pivot pins are ok) Also, am I going to have to remove the tracks from the floor and top of closet in order to slide the caps in from ... (cont.)

It appears that these doors were already make shift to me. I originally thought the nylon was threaded but it just appears that the bolt eventually pushed through the door pin cap.

I have a FULL-VU closet door composed of two bi-panel elements. To repair it I started to document each element: top pivot 5/16" top glide 1/4" bottom pivot 5/16" bottom glide 1/4" A very wise decision as there appeared to be only simple pins and such. Actually each of the four locations, a ... (cont.)