Viewing all customer Discussions for:

21-058 Bifold Door Guide Pin, Leigh, Monarch

My kids room bi fold closet doors one side upper parts are missing. I added pictures and the model is S 914791. Which parts should I buy for this?

Plastic sliders compromised, do not hold on to Inside pins where the two doors close.

Hi, I need upper and lower guide pins for the metal bifold closet with the attached pictures.I am not sure of the size. I have 3 closets with the same issue. I am not sure if I need 3/8 inch caps or 13/32 inch caps or different sizes. Thank you very much.

Hi , I am trying to replace hardware ( 3- pins pivots etc) to fix "one)leigh full view bifold door.

My bifold mirrored closet doors are misaligned as you can see from images 01 and 02. The left door is little lower than the right door. I am not sure if it's a problem with the door or is it due to missing hardware. The hardware that is missing is in image 3. Not sure what do I call that, but is the ... (cont.)

Trying to figure out these parts for metal bifold doors

I am looking to replace all the mounting hardware for my 96-inch bifold doors 1975ish (full-vu. Model 8433 Serial 861097 I just want to make sure I get all the correct parts or any missing parts. If any kits work, I have no problem replacing the tracks. Thank you Paul

One of the bifold doors hadn't been working. In continuously lifting it up to close it I bent the top pin (the one with the spring). The door came off and comparing it to the one on the other side I definitely need the plastic "thing" as shown in picture 21-058. The only thing I see inside the doors ... (cont.)

The track is approximately 3cm wide, the pins that go into the track have slides at stationary pins and rollers at doors that open. Some of the rollers are missing.

Hi, We are looking to replace hardware for our metal mirrored bifold closet door 3' opening. Attached is a photo of some of the hardware pin & slide. The door has to tracks top & bottom and was installed in the 1980's. Thank you. Rodger & Ivy

From a 45 year old metal bifold door

I am looking for a hardware kit or Pins, springs, caps to repair my 1970's FULL VU Bifold closet doors...Please excuse the dirt & dust! The tracks are completely fine but I need all hardware to repair/completely reinstall the bifold closet doors onto the existing tracks. I don't even know what ... (cont.)

These are what I think to be Leigh 70's era bifolds- looking to find similar parts and tracks for identical bifolds in another room (for a 10' opening) which were completely uninstalled and are missing all hardware, including original tracks

Would like to buy hardware for the following 2 doors. Leigh Full-Vu Metal Bifold Doors. Attached find label of door. Pics of the 4 corners of the door. Do you have replacement tracks for these doors? I can see that a spring and cotter pin is missing but have no idea if anything else is missing. ... (cont.)

No markings on any of the parts, unknown maker of the metal bi-fold door. Removed pin not knowing pics needed before removal. Pin in pics is 5 1/4" long x 1/4" diameter. Spring and cotter pin were on it. Plastic gasket in bottom and top of door holes (may be nylinders?) No plastic cap on top of ... (cont.)

Hi, sorry I don't have better pucs at the moment. I was hoping you might be able to ID the door from these lower guide pin pics and provide a parts list for all the hardware. Or maybe point me in the right direction for how to ID them, I couldn't find a brand or anything. My parents and several of ... (cont.)

Need help installing bottom pin and metal closet door. There It's nothing holding it in place. It just drops to the bottom.

My dad custom built these mirrored bifold closet doors in the early-mid 80s. I thought I repaired them but if I'm being honest, it was probably a temporary fix. It seems like the tracks (bottom/top) themselves are probably fine. However, I could see a new bumper-- at least on the bottom track and d ... (cont.)

We have multiple of these Leigh metal bi-fold closet doors that are missing the metal pins and plastic guides/sliders that go into the metal track. Aside for the missing parts the doors are functional. We are hoping to purchase replacement parts. Any/all assistance would be appreciated. ... (cont.)

These are pictures my contractor sent me. He doesn't know the manufacturer of the door. Can you tell? What parts would I need to replace the existing hardware?