Viewing all customer Discussions for:

21-108 Bifold Door Pin Cap

My appartment complex has about 300 leigh doors, all it says on the doors is quality control approval number 559245 I need hardware kits for the pins and the bushings that slide in the rails both top and bottom

After I installed the newly purchased pin cap #21-108 & all nylinders, I feel that the nylon guides are very tight. It takes a bit of effort to operate the door. Your replacement part seems identical to what I replaced. What's wrong?

I think this is a very old monarch bifold metal framed mirrored door. One of the doors top pivot pins keeps popping out of plastic glide. When I look at the other side bifold there is a tiny screw in the plastic glide that is keeping the pivot pin in place. If you notice, in the pic, there is a ho ... (cont.)

missing the bottom end glide the photo is from another door that is in condo. Thanks Eric

I manage an apartment community and 50 units have Leigh Full Vu closet doors model 8433. We are looking for top left pivot holder, similar to the pin pivot bracket of 21-205 but there is a portion that folds and when the screw is secure it locks it to the track. We recently ordered the Bifold Do ... (cont.)

These closet doors "swivel" out perpendicular. We have two broken brackets at the top of two doors. The brackets have 2 plastic "H"s that attached with gromets to either end of their bracket. The "H"s are beveled. It's the plastic that has failed. The metal floor and ceiling mounts are in good s ... (cont.)

Do you have a bifold door pin cap like 21-108 but for a 3/8" wide slide opening track instead of a 1/2" wide ?

I have 8 of these bifold doors and on some of them, the upper and lower pins need sliders. RIght now the pins have no slider guides and are metal on metal. Attached are a few pictures of what the good sliders look like (upper and lower)and a shot or two of where the guides are missing. I am in need ... (cont.)

Your 21-108 looks exactly like what I need, however the opening of my track measures a half inch, and the existing pin cap (at its widest point) measures 11/16. Do you have one that size?? Thanks.

I have the Leigh Bi-Fold metal closet doors, with mirrors, I purchased some parts last week, the number of the plastic sliding clip I ordered is 21-108. I need to know if track # 21-403 will accept that plastic slide. I need a new correct track for this door. The door has a S215421 number on the ... (cont.)

I have attached files of pics I took of my doors. I hope you can confirm the parts I need to order that will work. My doors have tracks on the top and bottom. I only need 1pin for the top and 1pin for the bottom. The pics I sent show that the bottom pin doesn't need to have a spring. The pin caps ar ... (cont.)

I am trying to find out if the bifold pivot on the bottom of the Full - Vu door requires a spring to push up or push down the pin that attaches to the bifold door pin cap. Where are are 21-049, 21-050 and 21-058 used, for the top or bottom of door ?? The pin that is there now thou badly ru ... (cont.)

Leigh Full-Vu metal bi-fold doors. Coopersville, Mi. I need 6 pivot pins, 6 guide pins w/ nylon caps, 10 springs, and 4 rubber stops. Thanks

Is there any other pin I can use other than the 21-108 PIN CAP. So that I don't have to remove the track where the pin slides back and forth on. Thank You. Dennis.......

The community here must have 1000's of these folding doors but our maintenence crew contends they can't find the parts. I would like to buy the parts to fix my own door and refer our people to where to get the parts. (I assume you can supply). Here are some pictures of the fittings on the doors. I w ... (cont.)

Your bifold Door Pin Cap # 21-108; will it serve on bottom track to hold dor pin in track? Does track need to be removed to place Pin cap?