Viewing all customer Discussions for:

21-108 Bifold Door Pin Cap

I am trying to help my father-in-law fix his closet door. My best guess is that it is a Leigh Full-Vu Bi-Fold door. The home was built in 75 and the doors are metal. The pins seems to be worn (possibly some broken parts). I was wondering if these four parts are what's needed to replace the four ... (cont.)

I recently purchased a rebuild kit for ~1980s mirrored closet doors. I cannot get the pins to stay in the pin caps as the pins pull out when opening/closing the doors. I reversed the spring tension on the doors(top: push up vs pull down to engage pin) and the pins still will not seat in the cap. ... (cont.)

Bought the 21-058 pin assemblies which use the 108 plastic guides. The doors are leigh 96 inch metal bifold. All the hardware seems fine and installed ok but the 1/4 pins seem to pull out of the plastic guides when opening doors. Is there any way of keeping the pin snapped into the guide tighter. ... (cont.)

Hello, Need replacement plastic sliders for top and bottom rails. The pin is 5 1/4 inch long, 1/4 inch wide. I would also appreciate receiving information about a full set of replacement parts (top and bottom). No idea who manufacturer was. Thank you in advance.

Bifold mirrored doors installed in 1984. The nylon slide/pivot in the top rail contains a slot into which the pin supporting the end of the door clips / hangs. Rail width is about 3/4". The slot on the left in the picture below of the slide/pivot has worn over time such that it no longer holds the p ... (cont.)

Need replacement bottom pins and a couple plastic sliders for the bottom rails. Pic1 shows top pivot pin (which I have all of), pic 2 shows bottom of a door, pic 3 shows the one bottom pin and the plastic slider that it snaps into. The rail is at (or just over) 7/16ths inch wide. The pin is 5 1/4 ... (cont.)

I Have a Leigh Product Bi-Fold Full-VU door and the Bottom slide broke will this 21/203 Pivot Bracket repair It? It looks like it might my house has several of these doors Here is a picture of it thanks in advance Gene

I need the pieces in the picture also bumpers maybe pin tracks r good

Im looking for the spacer or bumper that fit the number on the doorss between the top and bottom of the two bi fold metal doors i found one that looks looks like the ones I have but the length is 2" and the ones I have are about 1 1/4" The door pin cap# 21-108 should fit my track ... (cont.)

Building is built maybe in late 1960? I want to replace all pivot parts at top and bottom.

I need to replace these little plastic parts. After time, they wear out and do not hold the door pin in place. It's an old sliding door. Circa 1975. If you don't have these, can you recommend a replacement assembly? I'd like to avoid replacing the complete door. Thank you.

Hi, I want to replace all hardware on 3 of these bifold doors (including top and bottom tracks). The door openings are 4' x 8 '. All of the plastic clips are worn out and the tracks are beat up.

I need the screws for the corner pin bracket to reinstall my steal double bi fold closet doors on the bottom track. I could find two of the metal brackets in a drawer, but no screws. I have 2 of the complete sets in my cart ready to order, but wanted to know if I could purchase only the screws for t ... (cont.)

found similar pins but they we're 5 1/2" long

I have two sets of metal bifold doors that are old and don't work well. They don't stay in their nylon clips, are hard to open and shut, etc. I think the tracks are still okay, so I want to get all new pins, springs, nuts, and nylon clips for top and bottom rails (I assume you can replace those by r ... (cont.)

Need this plastic guide for closet track!

This is the peice that I need for my hall bifold door I've looked at home depot and Lowe's and can't find it..I would want 4 pcs of possible..thanks pam

Just bought a house in FL with older mirrored bifold closet doors. Structurally doors are in good condition however white plastic inserts in tracks are worn and I'm assuming pins should be replaced as well. I obviously need to clean up interior as part of refurbishing project. Swisco came recomme ... (cont.)

I've inherited some metal mirrored bifold doors with a house that I'm renovating and it's missing some of the hardware. I'd like to replace the footings that are in the tracks as well as they appear to be damaged (if that's possible without replacing the track). Looking for some guidance on all th ... (cont.)

The pictures show a pin which you have to push up and slide into the double-u shaped plastic slide. The doors are over 25 years old. I can't find the parts in any store such as Home Depot, Lowes, Ace Hardware and an old hardware store. I havae called every bifold door place and can't find the par ... (cont.)