Viewing all customer Discussions for:

33-080 #8 x 1/2" Flat Head Philips Screw

They appear to be nylon and sit at the edge of the lower window in a groove. I circled the item of concern in red. Better BILT is the manufacturer but have since gone out of business.

Is it possible to order and replace this part?

I believe this is a sash guide. I can't find these anywhere. Thank you for your help.

2 on each side of window. Plastic piece and screw.

This would be a new install. I have 4 swing out windows but no handle to push them out and bring them back in. I would like a rounded handle for the window frame itself and then a separate lock to keep the window closed. But I don't know what is available. There is a gap between the closed wind ... (cont.)

I have Brookhaven cabinets and recently broke one of the plastic sliding drawer holders. I don't know the product name/number but would like to order six (6) of these along with the flat head screws. the height is 1-1/4"

Attached please find some images of my old window frame that has its handle-bar broke off. Also, the little buttons of the release latches at the top of the frame are worn out. I wonder if you can have any accessory parts or suggestions that I can use to fix the problem? I know the broken bar that a ... (cont.)

Hi there, this piece which is simply used to guide the window open and closed (not totally necessary to function the window if we're being honest) is cracked! Do you recommend a replacement piece that might fit or snap in its place? Either a new handle or something to fill in the hole? The only mark ... (cont.)

Hello, Looking to replace latch with new Product Code: 82-269. Somebody used wood screws to hold the last latch in place and I am wondering if you could tell me what size screw is needed for the mortise as I saw that it doesn't come with replacement screws. Thanks, Todd

These appear to be a pull of some type

The picture is all I have to go by.

I have tried Knape and Vogt because the slide are made by them. But the bracket are not. Tenn-Tex doesnt' make them either. THey suggested I try you. The plastic cracks as you can see in the photos. I need to replace several in my kitchen. Do you have these or something that I could adapt. They are ... (cont.)

I am trying to find out if the replacement handles and base plate shown in the photos above are available. Each base is secured by two screws and the handle attaches to the window crank with another smaller screw. I would need hardware as well. Thank you.

Hi, I was wondering if you could suggest a quick fix for this vinyl window problem. The best solution we can come up with to remove the remaining "fin" and replace it with your part number 26-116, Window Sash Lift Handle, and mount it vertically instead of horizontally. We are putting this house u ... (cont.)

Hello :) CAN YOU HELP ME LOCATE THIS PART? (See photos) (Also included pictures of the wrong part below :) I ordered the 26-116 and it did not work for me. The holes do not line up. Thanks so much for your assistance!

All of our plastic lifts are breaking. In fact, my wife just cut her finger while opening the one in the picture. We need to replace all of our lifts preferably with something stronger than plastic. The lift measures 2 7/8" long and the gap between the holes is 2". Do you offer a replacement? Thanks ... (cont.)

Looking for the lower piece of this window. Only need about 3 ft piece. Not sure of correct name of part.

I recently moved into a Keller Home in Colorado Springs and wondered if y'all might know where I can get a replacement for this Window Pull? They measure 3"x3/4" The hole is 2 1/2"*1/2" The house was built 1996 Or any help identifying the Window Manufacturer appreciated.

Somehow we lost the screws for the nuprime window sweep lock 1-1/4", part 90-042, and the face mount keeper 7-8", part 90-041 Can you tell me the size of the screws needed for both parts? Thank you