Viewing all customer Discussions for:

33-081 #10 x 1/2" Pan Head Phillips Screw

Good morning! Please take a look at both pictures, one of them has a replacement crank for the windows and the other is the one that needs to be replaced. You will see the arm is stripped and I am not positive of how to replace this. It appears that there are replacement cranks(Gray window crank in ... (cont.)

Greetings We have just purchased an older home on Miami Shores, Florida, that we want to keep as original as possible. The house is filled with jalousie windows which seem to be all of the same make. See rhe attached photos. The most common problems are the missing machine screw with thw shou ... (cont.)

There are no markings on the part. Application is to operate horizontal windows on an enclosed sun porch. There are both left and right operators.

The two photos show original (silver) and replacement (beige plastic) hardware for this window type. Replacements were made by others. I cannot find any markings on the hardware except some circles. The size is 4-1/2" x 2-1/8" plus the flanges. There are four sashes per window. Some of the existing ... (cont.)

Is the 33-206 the right size, or the 33-207? Thanks!

Hi, I have several right and left operators that need to be replaced due to severe corrosion. They seem to match the dimensions for your 39-025 and 39-026 except that the arm extension is 2 3/16" center-to-center. All other dimensions are the same. Also, do you have any suggestions on how to ... (cont.)

This is on a window in the bathroom. It is a very old house. I could not identify the logo, possibly "ACP". The window only has 2 horizontal panes that rotate. I have had trouble verifying the dimensions when comparing online diagrams.

These are to windows that were built in the late 50s. The frames are aluminum and have horizontal glass panels. There is a handle that attaches and you turn to open. The dimensions are from screw hole at bottom to screw hole at top = 5 1/4". Bar that attaches to window pane, that comes out of the h ... (cont.)

Distance between lower two screw holes of base: 1- 1/8 " Between top and bottom screw holes of base: 5-1/4" From bushing to joint: 2-3/8" Not sure how to size bushing.

The spline appears to be broken, although it will open the window but refuses to close it. The spline comes right out of the operator and appears to have broken off. Very confusing.

I am looking for replacement jalousie window operators for my parents' sunroom. The windows are approximately 20 years old. The original operators are brown (or bronze) in appearance. One of the operators has the following information cast into the parts: On crank 11500-11 PAT PEND Inside stat ... (cont.)

I bought the 26-297 pivot bar(order 758466), and now I need the screws to lock it into my sash. I need something that's going to bite into that metal. I have vinyl tilt windows.

I have these old jalousie windows in a house under renovation build in 1950 (according to scarce records). It contains three types of windows 1) There are 6 36x50 windows each with 3 panes that are 32x14. 2) A bathroom windows with 1 pane. The window is 25x25.5 3) 1 kitchen window 36x25.5 with ... (cont.)

Hello I am looking to replace the cranks on about 10 jalousie windows please let me know if the pictures I sent are enough to identify them Thank You Greg

ref: awning closure 39-025. I recieved parts as ordered...installed one works well...second one i attempted, awning window doesnt close all the way. I did lose a bushing that goes in crank hole...and you sent no screws or bushing. could the lack of the bushing prevent closing if so, how do i obtain ... (cont.)

Our home was built in 1958 (I think) and has the original awning Windows. Three of our crank mechanisms need to be replaced and I am not sure what to order. I have attached 3 photos. There is an ID inside the housing that says 1 RH. Can you help? Thanks so much! Alison

I would like to order 2 of the above-captioned locking handles but I also need 3 sets of fasteners (screws). What screw is required? Can you also provide the screws?

Please let me know if your company has this screw available.

Hello,The mechanism has become stripped, and the windows won't close or close with great difficulty. according to this page: your Product: 39-278 will replace our old cranks. I just want to be sure about the 3/8 inch hole. Please see my picture I've attached to this email. Do the two products ... (cont.)

Hi!! Do you carry this part? Pan Am window operator inside of the mechanism is stamped: 4RH 18-0821 I am looking for 9 each of the entire mechanism to include new screws. The color is the aluminum color. Thank you for your assistance.