Viewing all customer Discussions for:

32-089 Drawer Track Back Plate, Pair

Drawer slide has an NL CO stamped on end.see photo.Slide is 21".From a Quakermaid cabinet. Probably 1968

Left and right hand brackets

Trying to find replacement hardware like this or similar. Must have a back bracket to attach to the back of the cabinet

these have broken over the years. I will email a photo separately from my smartphone. The internal width is 1 1/8" as best as I can measure; length 3 1/4'. the drawer slides (which I don't need to replace if I can find mounting sockets to fit them) say 550/22L and 17002-83, made in usa the ... (cont.)

Hello I am looking for these parts, both left and right sides. The side rails are unigrass 6600 series and measure 19 3/4 inches. I also need the back holding bracket both left and right the bracket moves back and forth left to right with markings on the back that say pat's 5.359.723 and 5.349.723. ... (cont.)

Looking to replace a couple of bent drawer, glides on my kitchen cabinets.

Need pair of these end brackets for Ferrari drawer brackets. Please advise.Michael

Need replacement for Ferrari GO24

So hoping that the picture that I clicked on or any other brackets you have no dimensions I know what they look like but I need to know what the dimensions are because the ones that I ordered were too short. I need one that is longer that would be able to hold the drawer in place when you pulled it ... (cont.)

The above picture is the drawer back plate right side to a York Cabinet drawer. These cabinets and drawers are about 30 years old. Can you match this up for me?ThanksSteve

I have a need for part number 60.1890 approximately 20+ pieces. Track is fine. Do not see this part on your list.3/8 x 1 is the opening. receiver is approximately 2 1/4 ". Remodeling a kitchen, hate to buy all new glides if not needed. Thanks, Ron

Hi, I am looking for a replacement for a discontinued Scheirich part that others have asked about also (the one that mounted to a metal rail in the back of the cabinet). Am I correct that your 32-089 will accept a side rail that is exactly 1-inch wide? Thanks in advance!

I'm looking for several sliding drawer supports. They attach to the rear of the cabinet and the drawers slide along the track. I'm guessing this hardware was installed in 1991 or 92. Please let me know what additional information you need.

I'm needing to replace this piece on the opposite side. At some point someone tried to replace with a part that doesn't hold the track properly on the bottom. And it also broke from the weight. These are large drawers. Ignore the zip ties. Apparently they were holding it together since the last piec ... (cont.)

I don't know the manufacturer of the rails but have been using Richelieu plastic brackets that are too small and constantly break. I need at least a 1" slot to fit the rail. Mounted against the back. If you have them, I would like to get about 10 pairs. Please let me know if you have something to re ... (cont.)

Kitchen draw slides end of track mounts. old brackets were nylon .437" by 1.0" track size. Old brackets approx. 2" in length from the back of cabinet to front of cabinetAnything of this size in stock ? Would take two pair of bracketsif they are in stock. Please advise Dave

Good morning - I am trying to find a replacement piece for a broken Grass drawer slide. The words Unigrass 6600 is imprinted on the broken piece as well as "RD". This came off the right hand side of the drawer. The broken piece measures 21-5/8" long. I am attaching some pictures for reference. I am ... (cont.)

Please help Identify what product I need.

I have old shrock kitchen drawers and the plastic back plate cracked. The track has a width of 1 inch and the it seems that the plastic back plate is 1 1/16 inches wide.I called Shrock and they no longer have any parts.The glide is 21 1/2 inches long and the back plate is 3 3/4 inches and the tra ... (cont.)

I also need a KV1284-3 socket. The slide entry area is ? inch horizontally, and 1 ? inch vertically. Your 32-014 is only ¾ inch vertically. DO you have anything that matches my dimensions?