Viewing all customer Discussions for:

S385-27 27" Series 385 Channel Balance

The sash channels I need to replace have the imprint 86-26-4 CB5 CMC-866. I am assuming this is equivalent to the 2640, please confirm or correct.

The string and one small part on the end was broken one day, and i think need to replace the whole part. could you find this? what's the cost of the part and the shipment to San Jose, CA. thx!

Balance is 1/2" wide. Metal part of balance is 27" long. If including plastic boots, the entire balance is 28" long. The bottom boot has #15P102 and a 3 below that number. The other balance's bottom boot has the same part number but a 4 below it instead. I can't seem to find any part numbers for the ... (cont.)

Definitely 27 inch metal part. The ends are definitely one inch, not 1 and 3/32". The stamped marking is confusing me. All I can find is 26B. Can you help me with this information and theses pictures?

I'm trying to make sure I get the correct non tilt winged Caldwell window balance

Do you have this part in stock? And how much? Thank you!

Hi there! I choosed your balance series 385-27 the exact replacement of my existing window but I cannot locate an option of 26-3 which is the markings indicated on existing channel balance. What is the number option that I will put in my order? Thank you:)

I see you have a 27" S385-27 Channel Balance that looks like it might be the same? Number on my part was 2630 followed by a upside down backwards F. There is also B.S.I. Stamped after the number. Would these two items be a match? Also, what is the difference between the series 385, 395, etc. Help! ... (cont.)

I need to find correct part# for 2 Sizes of window balances both 1/2" width but one is 27" long and the other is 15" long. Measured just the metal piece not the two plastic fittings on the ends.

I have a roughly 28.5 x 57 window that I need to repair. Attached are photos of the piece that came out as I was attempting to close the window. The metal piece measures 27".

The marking on the balance is 26 5 FR CALDWELL The length of the metal part (not including the shoes) is 27". The bottom shoe is 1" deep measured from the wing to the other end (measured at 90 degrees to the metal channel). I think I have to get 380-27 27" Series. Could you please confirm that th ... (cont.)

Can you tell me which one I need to order from you guys. Thanks Randy

I need both right and left complete set. 17 inches long 3/8 inch number marking is 26 4 B.S.I 2006 build year from Karsten Manufacturing

I need six window balancers please....

I have two windows which need to have the sash balances replaced. 1st window has numbers listed as: 26 4 CW CMC 10 and the pictures are for that one. 2nd window has numbers listed as 20 4 LV CMC 2. I had to put that window back together so didn't get pictures for it but the sash balance looks the e ... (cont.)

This is my window balance spring which is 27" long and 1/2 channel. Please let me know the replacement for this? Thanks, Mark

It's 27 inches long and 1/2 inch width . Please see photos. Has markings ie 26 4 EV CMC 7 and the other has 26 4 DV CMC 7. Please help me identify the correct parts. Thank you.

Please help me find/order two replacement springs for my window. Thank you in advance for your assistance =)

Metal only length 27" 1-2" wide 5/8" deep The black ink on top stamp 26 3 GW CMC 11

Hello: We have single hung windows that need replacements balances; could you recommend an appropriate balance? Please find photos of the markings, as well as views of each end. Thanks in advance.