Viewing all customer Discussions for:

32-118 Back Bearing

Good morning, I need to order some drawer guides for my Bassett chest of drawers, however I can't figure out which part number! Can you help? Thanks!!!

I am replacing rear guides that were installed with furniture tacks, so I don't have screws. What kind will I need to install 32-118?

Hi, I have a Pennsylvania house hutch purchased in 1995 and I love it. Unfortunately, the drawer guide is now broken. The marking are 40-28. Pat #3.201.187. I believe your 32-118 is the replacement. My question is how do I attached the guide to the drawer? Do I need a special staple gun? When ... (cont.)

I tried a bracket that looked close, but the bearing that runs in the slide was slightly too small. Any suggestions? Outside dimensions are approx. 1 3/4" H X 3" W outside, 5/16" H X ! 3/16" W bearing. Thx

looking for drawer socket. Possible furniture designed by Chris madden. Purchased 2002.

I measured my back guide as having an inside opening of 1 1/4" by 1/2". 32-118 seems to fit the bill except for the height of 5/16". However, it looks like there is a center rib support that could be knocked out (or using a Dremel, cut out). Is this wise? Or does a deeper guide exist. I cou ... (cont.)

Pennsylvania House drawer chest and armoire - purchased around 2007. Opening at base is 1 1/4". The top part of the glide is 2 1/2". Opening where wood on drawer slides is almost 1 1/4". Please let me know if you have all the info you need and if it is clear. Any help would be appreciated. Thanks. ... (cont.)

The slide I need to replace is from a High Boy drawer and the plastic that holds it to the track in broken. It is a standard size and I've seen them many places. All of the drawers have this type of slide at back to hold to a center wood track. Also want to replace several worn side glides on low ... (cont.)

I attached a picture of the piece I need. It is plastic guide that attaches to the back of a drawer. The main opening in the plastic piece that the drawer rail fits into is 1 3/16" wide and 5/16" high. The piece height is 1 7/8" tall and 2 3/8" wide. Also do you carry replacement dresse ... (cont.)

This is from a Fisher Price dresser/changing table, purchased in 1988. If necessary, I can try to get a model number, but I am currently unable to do that. Thanks for any help you can give me!

I am needing to replace a drawer guide on my Bassett chest. It was bought in 1999 from Sears. Do you have any pieces like the attached picture? It is 2 inches by 2.5 inches. if you need more information, please let me know. Natalie

Looking everywhere for this part.

We purchased some furniture at a local retailer Gardner's Furniture) a few years ago and the drawer guides have broken, which allows the drawer to drop to the floor when it is opened and not supported. The furniture was manufactured by Hooker Furniture, and when we contacted them they indicated tha ... (cont.)

I need a replace for a Broken drawer guide which is used on a one inch wide wooden track. Thank you

I am looking for (2) of these plastic drawer guides for a dresser drawer that has a label Chris Madden by Basset. Do you have this part and can I purchase it? Thanks

I am in need of replacement drawer slides that will fit the above numbered Ronthor-Reiss part. The uninstalled slide is broken, the installed is a replacement I had saved from when the dresser was new. The measurements are 2 7/16" wide at the top, 2 1/2" just before the taper, 1 3/16" opening wher ... (cont.)

Hi I am looking for a replacement rear drawer guide for a Bassett kitchen island drawer. The piece itself is 2.5" long.

we have a white plastic drawer guide that needs replacing. The dresser is about 10 year old. The part reads "Ronthor Reiss Corp N.Y.C R-40-28 Pat# NO 3,201,187 the part is 2 3/8 inch long. I have attached a picture I would like to know how I could order 4-5 spares

I need to buy replacement slides as all of mine have broken off. Its a set of circa 2002 basset Mission style bedroom furniture. Thanks