Viewing all customer Discussions for:

39-028E Ellipse Style Single Arm Operator, 9-1/2"

I purchased parts from SWISCO but found they were not the correct parts. I have attached a photo of mine hoping you could help me find the correct parts.

I am looking for cranks that are similar to your item 39-028, but with an arm length of 11" instead of the 9 1/2". If you can locate, I will need both a left and right in the Dark Bronze color. The 11" is measured from the same point as in your picture. Question: if you do not have an 11", would ... (cont.)

Hello, I have a Pulte home built in 2002. The casement window above the kitchen sink has a stripped gear that is going to eventually prevent it from opening. Can you help identify a replacement part?

Hi, I have some really old looking window cranks. I have 14 total. 5 are broken. I would like to replace them, if I can find the right part(s).

I am pretty positive I need 2 -(left and right)Truth window casement operator parts #39-027E. Here's what I need to know before I order. On YOUR measurement for the single arm in a part photo, you have 9 1/2 inch arm. In YOUR measurement drawing in one of the actual photos, it says 9 1/2 inch arm f ... (cont.)

Hello, I need to replace the operators on a few old Possi casement windows. I have attached a picture of one for comparison. The only part number on it is 07702-00. In one of your previous postings you recommend a 39-014 and 39-013. Would your part number 39-028 be an exact replacement? Also, the ... (cont.)

Hello, We are looking for a replacement crank for an old Andersen window, item #7073B. I did find a thread online that suggested your 39-027E and 39-028E however the arm doesn't have the same bend in it. Please see attached photo. If you do not have a comparable crank, do you have just the corkscre ... (cont.)

Markings: Truth, 45034-lh. Arm looks to be around 9.5" from pivot to end.

Hello I'm interested in purchasing a replacement casement from you; however I'm clueless as to what I should order. I've attached a pic. Could you please help. Thanks!

Part is stamped RH. 9.5" arm. Down offset. 3.0" x 1.5" (center) holes

Think I need part numbers 39-413 and 39-348? If so do the clips come on the sill mounted operator? Should I replace the shoe studs? What are the dimensions of the crank body as I measured in my pictures? Are they the same?

Dear Swisco, I am seeking replacement hardware (hand crank, worm gear, bracket, and toothed lever arm) for a Patriot brand kitchen casement window. The spline for the hand crank is stripped and the worm gear / toothed lever interface is also stripped. The two photos show the spline and the visi ... (cont.)

Do you recognize this part? If so, what do you recommend as a replacement? Please review attached photos for hardware identification Thank you Joyce

I recently purchased two replacement operators (39-028E & 39-027E). They fit nicely and will work with the windows. However, the plastic wheel on the end of the new operators did not match the existing tracks. The old tracks and old operators had the thin, flat plastic wheel. Now I need to replace t ... (cont.)

It's a Patriot brand window in my Kitchen

Two-window set in kitchen. Left crank was stripped. May need to replace both for matching pair. Left side has been removed; picture of installed crank is right side.

When turn handle - gearing in base jumped or skipped a gear so unable to open and close. I am the home owner but have an experience handy man guiding me and will do the work.

looking for crank and arm for casement window

Hiya, hope you can tell me what product is same as this: Wright 6077 stamped on both the left and right cranksets. Does anyone make this in stainless steel. Or bronze. Or enamelcoat? Thanks!

This is a double arm operator, with the longer arm about 9". The operator says Wright, and the crank handle says Hurd. The mount is rectangular, and the color is nickle