Viewing all customer Discussions for:

26-122 Vent Latch

I have a project with some missing vent latches. I was hoping you could help identify the part number if you carry it. Thanks

Hello, this part holds the window in place and has a tab that can be pushed to pivot the window in and out to clean. This one came from the left side when looking at the window. Lmk if you need additional information to match up the correct part. Thanks, Mike

My latches have broken. I can't figure out how to take them out. Do you have a video showing that? 5/8" x 1 5/8" are the measurements. I would also need the part numbers so I can order them.I also need a few of these stops. Part numbers too.Thanks,Dave

Please see the attached parts that are needed Nichole

Top length is 2 5/8 and top is 5/8 wide.......photos attached Your help in this matter would be greatly appreciated. J Chyson

Pat #4.923.230 Pat# 5,248,174 Used to prevent the open window from opening further

This is the gadget on each side of the vinyl tilt window that prevents the lower window from rising far enough for someone to get in.

We need to replace a number of these window locking springs. I'm assuming it doesn't matter if they're right or left sliding windows?Also Need directions on how to remove the existing ones. We're a couple of old ladies here and we can't open our windows past 2 inches because of this problem. Please ... (cont.)

After washing windows, did something that caused both windows to slam shut. Image of shoe is of one that is still intact. Top plastic piece popped off on others and may have fallen out the window during cleaning. The shoes are in decent shape, except for the small part detailed in one image. Don ... (cont.)

These go in the bottom of my windows. They are four to a window.

I'm looking for a vent lock for PlyGem window, with this info on window: PG3DHBS, 03165-281.Vent lock has this info on it: Pat. #4,923,230, Pat. #5,248,174. 14.I found your part 26-122 Is this the right replacement part?

I have a bunch of American Craftsman 8501B windows (around 15 or so years old) that need window latches. The hole measures .274-.276 inches wide and 1.862 - 1.871 inches tall. The outside of a functional latch is .367" wide and 1.962" high They looks exactly like 26-122, but the dimensions are of ... (cont.)

Here are some pictures of my windows...am looking for replacement parts of the locking device the stops window from being opened too far, and the locking device that allows the window to tilt out. Thank you, Dave

need this part - the spring eventually fails

Please help I need a vent latch for 2 and a pivot lock shoe how hard are those to replace?

Lock release

Can You see the picture I posted? These are 2" tall. Don't know the brand. Vinyl, approx. 2' wide/ 4' tall. These locks are so you can leave window cracked/ still secure. Do you sell these? Price? I need 2 or 3.

The other assembly in a window is broken. Our window will not stay up as a result. I think the window is Milgard but I am not sure. I can't find any branding or part numbers on the window anywhere. I am also missing one of these white plastic window pieces. Could you help identify them? Thanks. ... (cont.)

I am looking to repair a tilt window. I think I found 2 of the pieces I need on your site: https://www.swisco.com/Pin/pd/Tilt-Window-Replacement-Sash-Pivot-Bars/26-415 https://www.swisco.com/Vent-Latch/pd/Other-Replacement-Tilt-Window-Hardware/26-122 But I'm not sure which pivot shoe I need. I ... (cont.)

Hi, my 2 window vent stops were broken and we disposed of them. I would like to get replacements. The opening is 1" Length x 3/8" width x 1 1/2" Depth. I took a picture of a replacement for a different window to show you what it looks like. Do have two replacement parts?