Viewing all customer Discussions for:

39-105 Stainless Steel Detach Clip

Hello; I need to replace 7 Window Cranks. I tried the manufacturer (G-U) but despite providing a picture and exact measurements, they sent me something different from what I ordered. The result was a return and a refund. I tried a local distributor. However, whereas the original part had the P ... (cont.)

Question regarding the sash device 39-398. Once installed is there a quick way to detach the arm so that the window could be used for emergency evacuation? Also, will this device work on Milgard Sash Windows. Please advise

Hi I am looking for the following Window locks and crank mechanisms Image, 0387,0386 and 0384 are of the locking handle, The remainder are of the cranking Thanks Gerard

Hi there, I need to replace a split arm operator and the Maxim Dyad Sill Mount operator (product code 39-221) looks similar to mine. I notice that there is a mounting clip underneath my existing one (Please see attached picture). Is that okay to install yours by just getting a clip to hold the pin? ... (cont.)

Trying to identify this crank. SThanks for the help

Hello. Could you help me locate what I need. Three of our 1980s windows have trouble with the operators. The right window totally rusted out the bottom link which I cannot see in your models. It seems to be for support. You can see it in this picture. This is the best one. They all should be replace ... (cont.)

It seems the gear is stripped and will not open or close correctly. The part number looks like 45136 with a pat # 4505601

Looking for replacement casement window operators

I need to find a replacement for this split arm operator and locking handles. Here are the measurements I came up with hope this helps thx.

I am in need of Delmar window parts for which I have attached pics. (1) crank mechanism, 4" body width. (3) securing slide brackets. (2) lock handles with pins I also need (6) screen retainers (turning butterflys that capture screen inside the room). Thanks, Jeff Anderson DID THIS GO ... (cont.)

Hi. The plastic on the surface bracket broke and I can not find this piece. It is Roto brand and the aluminum is 6.25 inches long. Any help to get replacement parts would be appreciated. The model numbers are from the bottom of the crank unit. OP06-1505 OP06-7590-08 09-14-11 111066 ... (cont.)

Looking for this part

Lost this keeper that holds arm to window

We recently bought a house in Denver Colorado and one of the casement windows is missing the entire operator mechanism. The window is one of a side by side pair and it's mate has the operator so the pictures below are of that operator. The two windows swing opposite directions so I need the opposi ... (cont.)

Hello, I sent an earlier email via your website but after some research I realize that the info I gave you is probably useless. Therefore, I

Photo 1 ...left side picture of the same part needed on the right side window (window bracket and clip) Photo 2 ....missing bracket and clip from right side window Photo 3 ....I have one cover, but need second cover for right side and 2 handles ( one for each side)

Looking for the 3-piece assembly that connects the awning window to the extender arms. I have 33 of these windows of various sizes - the clip assemblies are all identical, 2 per window. Windows are about 8 years old.

This aluminum clip part is holding the arm to window. It is banded. I would like to order part in about 10 pieces.Thanks. Regards, SI PAE

Hi, My part that I need to replace is from a K&K window and its dimensions match your part 39-031. However, as shown in my photo, the bend or kink in the short arm of my original is in the upward direction. What direction is the bend in the 39-031 and can I use it to replace my part (as I said, th ... (cont.)

Hello, I was wondering if you might be able to identify this part for me? The number stamped on the crank piece is 20810 and the # stamped on the underside of the end piece is 20545 I've attached a jpeg. Thank you Martin