Viewing all customer Discussions for:

58-135 25ft Bubble Seal, 3/16" x 11/32"

Hi, My in-laws are trying to find the brand of the windows in their house. The builder has passed away and the original owner does not remember and we have found no identifying labels anywhere. The crank out hardware is TRUTH hardware and the only other name was on the crank which is SEMCO which cou ... (cont.)

I'm looking for the lower T-slot bubble seal and possibly for lift pins for some windows which I believe are Jeld-Wen dating back to 2003. The lift pin itself is 1/2" long by 0.050" diameter. The base portion is 0.440" diameter. This pin appears to screw into the window's extrusion. If you have ... (cont.)

Hello a have to replace this weather gaskets for a customer please get back to me as soon as possible just need someone to tell me the code of each gasket so I can Order, I believe they are Kolbe doors and need the complete set. Thanks Peter

weather seal on bottom of window

I have the above storm door and noticed that the bulb weather stripping along the top of the windows has deteriorated and needs replacement but I'm not sure which one to use.

Looking to replace bottom gasket and seals on the side windows also need the plastic part that The window attaches to

This was used for my transom door on my Tiara boat. AmersburyTruth Pt. 32021 doesn't make it anymore. Looking for an equivalent.

The middle strip cross section in the first photo (0600) us shown installed on the side casement, perhaps where the doors meet when closed.

Ok last one I hope. What type is this?

I have Hurricane windows. 1) I need 6 1/2" non tilt Channel Balances that are 23" long, Part Numbers 2290 BSI RF 28. I am not sure of the strength. 2) I need 12 1/2" non tilt Channel Balances that are 16" long, Part Number 15DS BSI RL 23. I am not sure of the strength. 3) I need 18 Tops ... I believ ... (cont.)

Hey guys looking for this part for my sliding patio door. No place I can find the manufacturer. Any help is greatly appreciated

I'm looking for bubble seal like the one in the picture.

I am looking for the round foam seal at the top and bottom of my windows. They are Vinyl Anderson windows I believe and are about 20 years old. The round foam piece has separated from the part that slides in the window and the foam tube is about 1/4" diameter now. I assume that it may have been larg ... (cont.)

There are no markings or name on the frame or glass. It is an aluminum double hung style window, only the lower window moves. It uses spiral rods for the tension/support spring. The seal picture and drawing are upside down compared to the actual installation orientation. This seal is on the bottom o ... (cont.)

I'm having trouble with Patriot double hung tilt windows Series 2200 that were installed throughout our house in 1996. The windows have become very difficult to slide open and closed. Some of the windows have responded to using WD40 and silicone lubricant on the spiral balances, but some are still ... (cont.)

Hello, looking for gasket similar to part# 58-135,3/16×3/8".looking for strp with 1/4"flat on bottom that fits into channel.please reply asap.thank you.

The weather strip is from the side of an Aluminum Awning Window. The red arrow in the attach window jpg shows it's location. I can not find any names or numbers on the windows. Thank You Tom

Hi Guys, I am looking for bulb seal that BF Rich used on the bottom of their sashes. Pics attached. Let me know if you have something that would work. White would work as well.

Looking for some assistance with replacement weather stripping for my home windows (built by NuAir Manufacturing in 2006, single hung aluminum). The stripping looks exactly like your item 58-135 with one exception (the t-slot is a bit more narrow at roughly 5/32). Do you carry something like that? ... (cont.)

Hollow bubble seal. Has a flat fin on one side. And a T slot on bottom