Viewing all customer Discussions for:

10-324 24" Shower Sweep With Drip Rail

Do you sell this replacement?

Please see attached photos. Just need the vinyl shower door sweep. The aluminum drip flange is perfectly ok. Do you have some that matches?

hi there I was going to replace this whole shower unit only because of the seals but I figured maybe I take a chance on just finding the seals first can you let me know if you can figure out what replacement parts I would need.. I also consider doing clear Glass, and if I purchase the clear glass ma ... (cont.)

Can you tell me at what measurement the screw openings are at?

I have an older Jacuzzi brand shower that needs a new vinyl strip but I cannot find the right match. The drip rail is 24" but one screw hole is 2" from one side. Will the 10-324 model fit?

Good morning I have a hinged shower door, my problem is, I cannot find the the plastic seal that goes into drip rail, I bought one from home depot, but when I close the doors the seal does not seat into the channel, I tried cutting it but still it doesn't work, I think the plastic is too hard, can ... (cont.)

Hello, my shower sweep separated from the shower door. The door has no screw holes to re-attach the sweep. What is the best way to attach 10-324 to the shower door? Are there any sealants or tape you'd recommend? Thanks.

I have been trying to find a replacement strip for a shower door sweep. See attached photos. The lip on the top of the strip has a slight downward taper. The width of the track on the sweep is 0.15 inches. Thanks, Fred

Please respond.

Please advise me what model shower door sweeper number is this. My is JohnI would to order two pc please.Pls advise ASAP.

The shower door sweep as shown above with the drip rail needs to be replaced but since there is no name on either the shower or door we have been unable to find any parts. We are willing to replace both the sweep and drip rail if easier . The actual width needed is 25 3/4 inches . Is there a part th ... (cont.)

where are the screw holes located?id there one in the center?

Hi,I purchased this and cut it to the required dimensions to make it fit my old shower door. But now the door does not close and gets stuck mid-way.To confirm that the rubber strip is the issue, I removed it and installed only the aluminum sweep and the door closes perfectly. So I cut the rubber str ... (cont.)

The shower door is not closing properly at the top. The plastic sweep on the bottom of the door is worn away. The seal around the glass door is deteriorating. The door is 67 3/4 x 23 3/4.So basically looking for parts to make the door functional again.Who is the manufacture of the shower surround? ... (cont.)

I need to replace the vinyl / pvc water seal on the bottom of my swinging shower door. It seems to be several peices I need. Can you tell me what to order? Thanks - Candace

I need to replace the rubber sweep as the black rubberis deteriorated. Do I need to replace the entire rail or can I just replace the rubber? The rail measures 25". Image attached. Thanks.

We purchased a house and the shower is missing the seeep and water keeps leaking out. Which one of your seeeps would work? Do I put it in the smaller space that is closest to the interior of the door or the larger space?

2 doors about 24? each Pic is of actual part Attach with 3 screws through bottom of door. The guides fit into 2 full length tracks pic House built 1960 Can not locate any product id

I need to replace the vinyl sweep on my shower door. It is a round or tubular shape at the top and the bottom part is 1/2 an inch. The shower door is a little less than 22 inches wide. As you can see from the photo the bottom part has separated from the top part that slides in to the bottom of the d ... (cont.)

Hope this picture is clear enough to identify part. Top tee shape is 1/4 inch wide. Drop down seal is 3/4 inch in length. Tee shape slides into a drip edge track on door. Thanks for any help you can find. Mike