Viewing all customer Discussions for:

82-265 Multi-Point Mortise Lock with Face Plate, 11"

In reference to the attached dual mortise lock, what is this made out of? Do you have a steel dual mortise lock?

Hello, I think your 82-090 item fits the same dimensions as my current handles except my lock lever is located toward the top area of the door handle (my images attached). The images posted for the 82-090 item have the lock lever toward the bottom of the handle. Do you have a door handle that has th ... (cont.)

you can see in 0-2.jpeg that the plate has broken at the bottom screw. THis is I believe lincoln patio door hardware, butI don't have any parts numbers. I did measure as below. I used a the measure, and while I tried to see 15/16ths, I might've missed a 1/16th here or there. Do you have just the ... (cont.)

Think this is from a Silver Line V1 series, there are no markings, no numbers.

I am looking for a replacement locking assembly for the Reliabilt 332 Series 70.75-in Model # 719801223692 Grilles between the glass tiny sliding door with screen. I need the locking assembly for the door.

I am thinking the 82-265 lock will fit my door, can you confirm this? The measurements on your website match the measurements of the attached lock. also, do I need a new handle to match the lock? if so, which one will work in white? (note: The attached lock is a replacement from several years ago)Sc ... (cont.)

I need to replace my sliding door handle that goes with MULTI-POINT MORTISE LOCK WITH FACE PLATE, 11" I could not find it on your site. Thanks!

I am attempting to obtain a replacement lock for my patio door.

I need the right multi point for this set

I am looking for replacement Or substitute for imperial USA door handle for my patio door. The length between installation holes is 4 inches

What handle set goes with the 82-265? This is my existing, i believe the 82-265 will work but cant find a handle set that is as long,this one is 9 9/16"

Hi Please I would to know if you have a siding lock door

hi, I recently bought the 82-265 mortise lock. It fit nicely in the sliding door, It doesn't work with the previous latch receiver (the part that it clasps onto at the jamb). Do you have a part I could buy that would work?

Need to replace the Mortise pictured. The 82-265 looks like its three right one. All dimensions match your website. I'm just not sure if the keyholes line up. The 82-265 looks to have 2 spots for the key and latch lever to go in. The one I have (pictured) looks like the keyhole slot is lower than t ... (cont.)

The distance between the mounting screws is 11". I operated the one deformed actuator and both arms extended as show in picture 368. There is one lever that operates both evidently. I would like to get a new unit if that is possible.

Top and bottom holes on white trim face plate are 11" apart (center) The 2 inside holes on white trim face plate are app 3 1/8" apart The 2 side holes oval shaped that hold handles on are app. 3 15/16" I think I found the right replacement at one point in my search on your website and you show ... (cont.)

Sliding door internal lock. Front plate is 11-3/4", holes are 11", distance between latches is roughly 5-7/16.

Hi IAM trying to find new patio lock set the only sticker I see on frame says nami 4821/2821

Hello, I recently purchased the 82-239 mortise lock but it didn't line up. The main issues: 1. On the 82-239 there are no holes in the new lock to attach the old white face plate. See attached photo of holes in the old lock and face plate (Circled). 2. The throw on the new latches don't see as dee ... (cont.)

i'm pretty sure I need part number 82?265 but I don't know 11 Inches on center means.