Viewing all customer Discussions for:

26-226 Pivot Bar, 3-1/16"

Could you please help me identify these parts. I have not been able to identify replacements anywhere. They have no numbers on them that I see. Your help would be greatly appreciated. Joe

I have 3 balances that have failed. I'm trying to identify the replacement parts to order. See attached photo. The pivot bar is 2.5" long. Screw hole is 1.25" from business end. The metal cam has failed. I'm assuming I'll need to replace the whole shoe. If I can get away with a cheaper soluti ... (cont.)

I am looking to replace a broken pivot bar for my vinyl windows. It's measurements match your part number 26-226, however the foot of the part does not look the same in the pictures. Can you tell me which part will work?

If there were markings or a brand on these windows, it's worn off. Hopefully you can help me find something that will work. Thanks, Chris

I need help finding the correct replacement coil balance for a vinyl tilt wash window. Aside from the pictures I took, is there any other information I can gather from the window to help determine which part I would need?

Dear Sir/Madam, The attached shows a pivot par I am looking for. If you have what it shows, I would like to buy four pieces depends on the price. Your help is greatly appreciated.

Hi Swisco, I need to purchase several pivot shoes that will work with the pivot bar in the picture. I previously purchased the 15-135 locking pivot shoe, but my pivot bars do not fit in the cam. Any suggestions on which pivot shoe will work with my pivot bars? t Thanks.

Hi, I am looking to replace 4 pivot bars for my window. The pivot bar is metal and 3" long by 1/4" wide by 1/8" deep. Please take a look at the photos to ensure that I took down the correct measurements.

I've got a 2-3/4" sash pivot bar that I am trying to find a replacement for. it has one hole centered at about 1-5/32" from the tapered end (about 1-3/8" from the circular side). I need 8 of these if you can find them.There is a "6" stamped on one side of the bar.

First image - Shoe (I believe) is broken on the top and bottom on two windows. Second image - Not sure the piece but the bottom of the window I think that goes into the shoe? I contacted the maker and they are stating they no longer have the pieces. The windows are only 8 years old and I need t ... (cont.)

I am finishing a job someone else started. They have already purchased the 15-129 pivot shoe. However, I need to replace the pivot bars as well. My question: will the 26-316 pivot bar work with the 15-129 pivot shoe? Thanks - Donald

In the attached images you will see my broken parts. The window weighs 6 1/2 lbs. There is the letter "F" stamped on the spring. Can you tell me what parts I need to order. The spring is 1/2" wide I have several broken window springs like this. The pivot bars are also broken on a couple ... (cont.)

I am looking to find 2 replacement pivot bars for my window sash. The identification number on them is 9862. Do you guys know where I may find them?

I do not know manufacturer of windows. I hope you have this part. No markings or stamping s on this part.

Installed Original New in 1998 Paramount Vinyl Double Hung Tilt Windows then the Company sold out to Winco then to Jeld Wen. Jeld Wen Cannot help. Several Pivot Pins are broken. They are Zinc Die Castings with 1 3/8 to Centerline of first hole with casting # 9762 1 and 9762 2 depending if right or l ... (cont.)

On your web site I found 85-864 But It is a little different size What do you think? Russ

Your 26-226 Pivot bar mates the size I need for my Bonneville windows (Double Hung) - however I need the Brake Shoe/Pivot Shoe to match up with it - searched you site a bit but could not fine the one I need - mine is 1 1/4" high, 1 5/16" wide and 11/16" thick. The metal cam is 17/32" across the fac ... (cont.)

Please see attached pictures. I think I identified the correct Coil Balance Shoe (# 15-175), and I was curious if you sell the cam separate? I need 6 of them. There is an "18" stamped inside the cam. Thank you, Alex

looking for sash pivot bar for Bonneville windows, purchased in 1997 from Home depot. Cast material.2 holes for screws- overall length 3 1/8 inches

hello, I am looking for window pivot bars, all I have to go by is the attached photos, please advise if you have a part like this. thanks, Steve