Viewing all customer Discussions for:

82-086 Legacy Keyed Handle Set, 3-15/16" (1-1/8" to 2-1/2")

I am looking to replace a broken handle/lock for my sliding glass door. I believe the handle is the original from when the house was built in 1998. The door may be a Hurd but I cant verify that. The markings on the original handle says PAT#5,092,144. P/N 120-60. Will the legacy 82-086 work with t ... (cont.)

I have an old sliding patio door with more than 11" length mortise, photo attached. I am looking for a complete replacement. Meantime, the following parts are ordered. Transaction ID: 3MT486890K677332K Invoice ID: 1556425 Please replace with the appropriate part if needed or send me the right ... (cont.)

I tried to install the legacy keyed handle set and the two tail end pieces for the locks don't fit into the locking mechanism in my door. I can slide one through but i can't slide both through.

I need handle and lock set that goes with those handle set. Patent D466787

Is there an option for a Kwikset lock ?

I believe the subject handle will work for me. I've measured based on your specs and all should fit. I also verified that the mortise lock is working. I have two doors thus two fixtures. I'd like to replace both with white handles. My question, if I order two can I specify that I want the same key f ... (cont.)

I am replacing a patio door handle that does not lock with the Legacy, which I already bought. I did not buy the part that inserts in the door because I already had one. When I went to slide the tail ends in, there was only room for one. Do I need another part to replace the mortise (is the right wo ... (cont.)

Do you know the part # or where I can buy the entire unit?

I need to replace the entire handle assembly, the lock / unlock handle broke. I don't know the model # or were I to buy it.

Hello, Is compatible the set above with my current installation on photos below of my Guardian glass sliding door to replace? Thank you for quick response, Viktor

I am looking to purchase a replacement mortise lock and compatible handle set for my sliding glass door. In my cart currently I have- Multi-Point Mortise Lock with Face Plate, 11" 82-265. I am confident that is the correct replacement lock, what I am not sure of is a corresponding, compatible whit ... (cont.)

Can you tell me if you offer a locking handle that will work with a Jekdwen 2500 sliding patio door? I purchased one from Home Depot but the offset is too great and it doesn't fit. Thank you

On the back of the handle on both side there is a few numbers,on top 2265,us patent 5125703 then D 340398 .please can you let me know which door handle can matches my old one and if 82-086 is a match.thanks for your help

Hi,I purchased this handle set with the 82-227 mortise lock 5-3/8 and it seems to fit just find. However the key is just spinning and not locking. What part am I missing or did I buy the wrong mortise?Kendra

Would like handles to fit mortise will product # 82-086 handle fit my mortise?

The lever on this sliding door latch does not stay on - see attached/detached pictures. I am looking for options to either replace the lever or the entire lock. If replacing the lock, ideally one with a low profile exterior handle would be preferred as there is not a lot of width between the door an ... (cont.)

Hi, I purchase the 82-086 legacy keyed handle set and require additional keys. However, no one in my area seems to be able to match the key correctly -- every key I've had made is too wide for the key slot. Do you have any guidance, or do you sell copies or blanks? Thanks! Christopher ... (cont.)

the lock handle I purchased is correct, its the Amesbury Truth # 82-086. but I did not order a replacement mortis lock for this unit. it seems the one currently in the door is worn out so the lock arm that comes out does not stay in the locked position when the key is turned back to remove the key. ... (cont.)

From the pics I took I believe the replacement I need is a mortise and tenon unit. measurements of it are: length of handle part is 9.5 in., length of unit in door jam is 4 & 1/8in., corresponding part in the lock part of the handle is 5 & 5/8in.I'm a widow and can repair lots of things but ... (cont.)

Is good for patio sliding door 80x 60 American Craftsman