Viewing all customer Discussions for:

33-071 #6 x 3/8 SS Pan Head Screw

The seal for our shower door was missing when we moved in 3.5 years ago. I couldnt find the right part and we don't want to replace the entire unit because we plan to remodel in a few years. I'm not sure what type of seal we need, but this is what the door looks like. Do you have anything that would ... (cont.)

I need to replace two spiral balances in a non-tilting aluminum window about 20 years old. I have identified the part needed as S400-30 green. However one of the lower brackets is broken, half of it fell out of channel during my investigation. I see that you sell brackets but they don't seem to ... (cont.)

The photos are my shower room door. It needs the bearing to close the door tightly. The diameter of the hole is about 0.7cm and the total diameter (including outside cover?) is 1.2 cm. Also, I need to attach blockage to the bottom of the door to block water leakage. It was consisted with aluminu ... (cont.)

What do you suggest to replace pivot bar in picture 2-1/2 "long 5/16 wide and 3/8 wide at wide end Your 26-021 matches all measurements pretty good but The bulge on end I worry about. The slides out of unit' Thanks Jack

Hello, I am trying to find this size replacement part for my shower; however, the one I currently have has 3 screws holding in place and it looks as though your product may only have 2 places for screws, is that correct??

30" Shower Sweep With Drip Rail Product Code: 10-325 I have a wooden door I am using as a shower door, It's a 28" door but the sweep would need to be 27" to fit. Can the 30" Shower Sweep With Drip Rail - Product Code: 10-325 Be cut down to a custom size? Because of the unconventional door, I ... (cont.)

We do not have the fasteners for the shower door sweep. Do you sell them? Thanks!

The width of a T part is 3/16. There is no manufacturer'name anywhere.

I ordered the bottom flap drip for the 24" shower pivot door. Which screws do I need to buy and where to put them on the new strip also which way does the new strip go

I need this part and no stores carry it. It's 21 inches long. It's the drip rail for my stand up shower and it's a framed shower.

I've got one of those builder installed framed (chrome) shower doors and am in need of a replacement. I saw the 24 inch which seems like it would work but when I measure my existing door it appears to be 26 inches from edge of door near hinge side to the end of the door just before the magnet. Obv ... (cont.)

Door sweep split. 2003 Coastal product. 21" long by 13/16" d by 1/8" top bead .I tried 1 on Amazon but it keeps slipping out.Do you have any thing similar?

18 inch 3/8

I need to replace the rubber sweep at shower door bottom. Issue is one of the screw is not tightening in the hole. Screw seems to be ok. I think the hole might have worn out threads. Need parts and help to fix this door sweep.

What are your views on using Silicone to install Track Covers 80-102 as is shown on some other sites? Will the Track Cover 80-102 not stay in place without Silicone? If Track Cover 80-102 has to be replaced again in future, will the Silicone make removal of old Track Cover difficult? ... (cont.)

The bottom flap or water stopper needs replacing. Do you sell that part and the screws? Please advise, Tracy

I need set of replacement screens for a tilt-out window that weighs 16lbs. I'm not sure which screens to order. I would greatly appreciate your help. Thank you

Hi: I already ordered parts S 140-20 x2 and 26-398 x2. Not exactly like my old ones. Here are pictures of my old ones. Can you advise what I need?

these are pictures of what I need, the other one disintegrated, so I sent pics of the good one. the tag is from another window in the house as the label on the actual sash in question is missing. The only marking on the spring is an F. the lock shoe only has a Patent # 6,983,513 and 5,371,971. Any i ... (cont.)

I am looking for a replacement for this broken glass shower door sweep. It is approximately 23.5" long, with two screw holes, approximately 17.5" apart. Do you have anything that matches this configuration?