Viewing all customer Discussions for:

39-011 LH Superior Window Crank

I need to replace this part wich open the window by crank the lever If you have the part let me know Thank you

Hi, I need to replace the window part shown. Original numbers on the part are D-198202us. RD 1963 Can 11500-3 2 R.H. I spoke one of your colleagues at Swiss o and he told me this is not your part but you may be able to recommend a suitable replacement. Thanks

Hi! I recently purchased a house with a bunch of the window cranks broken or missing. And quite a few windows that won't fully close. The house was built in 1959 and I believe the windows are original. There's aren't a ton of markings but one says superior windowco miamifla Please let me know if yo ... (cont.)

Unable to locate any part numbers or other indicators, and have been unable to match with any patterns in stores

Looks very similar to model 39-277 and 278, but the dimensions are: vertical distance between screws: 5 1/4" distance between the two bottom screws is : 1" , openning in the flat bar is 3/8". And the length of the flat bar between the two openings is 2 5/8"

I ordered 39-060. But it doesn't sound right

Good Evening, if you could please help me identify this window crank. It looks alot like the 39-061. Except there is a metal shank riveted to the arm that connects to the window. There is also a metal sleeve that slides onto the metal shank. Looks to receive a 1/4" machined screw. I would be incredi ... (cont.)

Replace handles on jalousie windows

I'm looking for a RH window crank. 5-1/4" top to bottom hole. 2 bottom holes 1-1/4 inch apart and a link arm with holes at 2-3/4 apart.

Looking for a Operator with 1 mounting hole on the top, two on the bottom. top to bottom spacing 5 1/4, bottom holes are spaced 1 1/8". the arm is 2 1/2" from the pivot pin, to the 3/8" non-threaded hole. Thanks, Bob

The handle will not turn window closed. It appears to be stripped.

Please help ID based on dimensions. Ty

Hello, can you please help me identify this and do you have a replacement one please? Thank you.

I need to replace it. I'm clueless about measurements, etc. I had ordered a replacement from Amazon, but when it got here I noticed that it had two holes at the top of it and the one in the picture only has one hole at the top. I had to return it. I'm asking my son to install it since I am in my ... (cont.)

Window doesn't close completely please attached picturesThe part appears to be 2" x 5 7/8". Approximately if you don't feel the operator is the issue please make recommendations. ThanksGavin.

Pat. No. 198202 U.S. 2 R.H.R.D. 1963 CAN I have tried multiple times to get these replacements, without success The single top hole to bottom R hole is 5 1/4 inches The bottom holes are 1 1/8 in apart The extension arm is 2 5/8 inches long and offset. The hole in extension arm is 3/8 in and fi ... (cont.)

No mfg. Or writing cept 14 3691*1

my operator's dimensions resemble all of the specs you show on your 39-025, with one exception. My operator doesn't have that sharp offset in the inner arm. Would that make a difference?

Hello, I received the item 39-011 to replaced my damage crank operator on my awning window, but I forgot to buy the screw that conects the crank to the awning mecanism. Which is the pad head or screw that I need for that? Thank you Andrea

Hello!I have 13 right and 2 left operators I would like to replace in a home in southwest Florida. The patent number D 198202 was found embossed in the metal cover. Could you please identify these parts for me so I may completely replace all?Thanks for your support,Wayne.