Viewing all customer Discussions for:

39-032 EntryGard Dual Arm Operator

Please can you try to identify from the attached scan, the

this piece seems to be the problem. Do you carry a replacement part?

One Right Hand model Window Operator by EntryGard TRUTH with 4and7/8" Link Arm 20310 and a 9" zoom Arm 3308428 measured from bolt to bolt, or about 10" as shown by the ruler from rotor to end as shown in my photo. If I identified the operator correctly it may be TRUTH's 15.10.00.002 Wally ... (cont.)

Kitchen Windows (2) Entry Guard Truth, 20810 is what is says on the window hinges. Do you have this part? what is the cost? Thank you

I need to replace both right and left operators for caradco casement window. Prt number showing is 40372. Do u have these? I would need to replace all components....cranks and covers.

I have a combination of single and double wood casement windows which I think are Pella but can not find a serial number. Can you let me know which replacements I should buy

Hello, I need to replace several crank mechanisms for windows made by Permanent window company. If you have them can you tell me if there's a way to remove the old ones without removing the wood? Perhaps a special tool? Thank you, Connie

Unik - CAN3 - A440-M84 Arm Part Number - R30842 / 2nd component 20810 Arm Part Number #2 - 30472 RH Brand description - EntryGard Crank Part Number - 30830

The 39-031 and 39-032 EntryGard (Caradco 916) operator is what I have. Is the central gear (in your picture available separately?

Looking for item listed above

The attached photo is of a Jeld-Wen casement window operator that has stripped teeth. The date of manufacture from the date on the window is 01-05 and the "model" on the operator is "Entry-Gard"

I need to replace a window crank on my mother's window. Inside the house, it would be the right window as you face the set of 3 windows side-by side. The crank on the left window has R30842 imprinted on it, but I need the opposite one for the other window. Someone did replace it for her a few ... (cont.)

I am replacing a Truth Entrygard window arm operator for a casement window opening out and locking on the right (hinged at the left) where the link arm is just over 3 3/4 inches long. Can you recommend a replacement part, because on your site I only see options longer (4 7/16) and shorter (2 13/16) ... (cont.)

Hi, these were on Malta windows from 1998 and we need to replace the sash and the crank. Do you have a part that will work? Thanks, Jacque L, REALTOR REMAX Checkmate

Good afternoon - the crank assembly in one of my house windows has gone bad. It no longer cranks the window inward. This is a left-side opening window, with part number R30842 stamped on one of the arms. The housing has worn away and cracked, which I assume is part of the problem. The crank arm ... (cont.)

Dear Swisco, I hope you can help me. My house is 19 years old and the windows came with the house. Four of the cranks no longer work. Not sure where to find the replacement parts or what is involved in repairing the cranks. If you have the parts please advise re cost and ordering specifics ... (cont.)

Looking for a more cost effective operator replacement.

The window crank piece had broken and items from inside the unit are attached and shouldn't be.

Hi, I have attached some pictures of my crankarm. From another post/response I am pretty sure it is the 39-032 crankarm I need. Can you confirm this or send me in the right direction. The long arm measures 10 3/4" (same length). The short arm measures 4 7/16" (same length). Part numbers - mai ... (cont.)

Hi, My part that I need to replace is from a K&K window and its dimensions match your part 39-031. However, as shown in my photo, the bend or kink in the short arm of my original is in the upward direction. What direction is the bend in the 39-031 and can I use it to replace my part (as I said, th ... (cont.)